Silver Cross Dream Manual De Instrucciones página 5

8
INSTALLING THE DREAM
I-SIZE BASE
Make sure that your vehicle
has ISOFIX anchor points and is
approved in the vehicle application
list which is supplied with the base.
Locate the vehicle ISOFIX points. If
this is a problem consult the vehicle
manual. They are usually between
the vehicle seat base and back.
1
Insert the two plastic ISOFIX
guides and hook them onto the
vehicle ISOFIX points. The plastic
guides can help identify the vehicle
ISOFIX points and make installation
easier. They can also help with the
protection of your vehicle seat.
2
Pull out the support leg from the
attachment.
3 Lift the paddle lever, centrally
positioned at the front of the base
and push the front support leg
housing towards the base to fully
extend the ISOFIX arms.
4 Connect the ISOFIX arms onto
the vehicle ISOFIX points. Firmly pull
the base towards you making sure
that both arms are connected and
check that the ISOFIX connection
indicator is now showing green
5
(parts list no. )
5 Again lift the paddle lever and
firmly push the base towards and
up against the back of the vehicle
seat. Make sure that the back of
the base is now firmly up against
the rear of the vehicle seat. Check
again that the ISOFIX connection
indicator is showing green (parts
5)
list no. . The base should now be
secure and stable.
ENG FRA SPA ITA DEU SWE FIN RUS ZH-S ZH-T ARA
6
Push the adjustment button and
adjust the support leg so that it
makes full and firm contact with
the vehicle floor. The two pressure
monitors at the base of the support
leg must turn from red to green
confirming firm contact.
Do not place the front support leg
on a floor storage compartment
lid. The front support leg MUST
make full and firm contact with the
vehicle floor.
Make sure that the support leg does
not raise the base from the surface
of the vehicle seat.
Not all infant carrier bases fit
all vehicles. For advice as to the
suitability of this infant carrier
base please consult the vehicle
application list before you purchase
the base and make sure that the
make, model and year of your
vehicle/s is suitable. If you are in
any doubt please contact Silver
Cross customer services on
0845 8726900.
7
Check that the front support leg
clicks into position and is correctly
adjusted.
8
Lower the Dream Infant Carrier
on to the Dream i-Size Base and
make sure that all 4 connection
bars engage firmly and click into
position on the base connection
8
points (parts list no. ).
Make sure the infant carrier handle
is in the upright position and that it
"clicks" into place.
9
Lift the Dream Infant Carrier to
make sure that all four connections
have engaged correctly and the
two connection indicators have
changed from red to green (parts
list no. 9 ).
DETACHING THE DREAM
INFANT CARRIER FROM
THE DREAM I-SIZE BASE
10 Pull up the release handle on the
back of the Dream Infant Carrier.
The two indicators on the front of
the Dream i-Size Base will turn from
green to red to indicate that the
infant carrier has been detached
from the base correctly. (parts list
9
no. )
11
Carefully lift the Dream Infant
Carrier from the Dream i-Size Base.
REMOVING THE DREAM
I-SIZE BASE FROM THE
VEHICLE
12
Only remove the base from the
vehicle when the infant carrier is
not attached. Disconnect the ISOFIX
connector arms by lifting either
or both release paddle handles
positioned on the side of the base.
The infant carrier connection
indicator should have turned from
green to red, the base should now
5
be disconnected (parts list no. ).
Push the support leg adjustment
button adjust the front support leg
to the required length and reattach
to the holder positioned under the
base. Carefully remove from your
ENG FRA SPA ITA DEU SWE FIN RUS ZH-S ZH-T ARA
vehicle. There is a carry handle
located centrally between the
ISOFIX arms to help you carry the
base. The ISOFIX base can be left
installed in the vehicle.
VERY IMPORTANT
Please read the whole of this
instruction guide carefully. Failure to
do so could put your child in danger.
The Dream i-Size Base can only be
used with the Dream Infant Carrier.
The child safety seat has been
designed, tested and certified
according to the requirements of
the European Standard for Child
Safety Equipment (ECE R129/02).
NOTICE
This is an i-Size Enhanced Child
Restraint System. It is approved
according to UN Regulation
No. 129, for use in i-Size compatible
vehicle seating positions as
indicated by vehicle manufacturers
in the vehicle user manual.
If in doubt, consult either the
Enhanced Child Restraint System
manufacturer or the retailer.
Other vehicles and seat positions
may also be suitable for this
restraint system.
NOTICE: DO NOT USE ON A
PASSENGER SEAT FITTED WITH
ACTIVATED FRONTAL AIRBAG.
silvercrossbaby.com
9