Ryobi EMS-2026SCL Manual De Utilización página 24

GB
F D
RULES FOR SAFE OPERATION
MAINTAIN TOOLS WITH CARE. Keep tools sharp
■
and clean for better and safer performance. Follow
instructions for lubricating and changing accessories.
REMOVE ADJUSTING KEYS AND WRENCHES.
■
Form a habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
■
Normal sparking of the motor could ignite fumes.
KEEP HANDLES DRY, CLEAN AND FREE FROM
■
OIL AND GREASE. Always use a clean cloth
when cleaning. Never use brake fluids, gasoline,
petroleum based products, or any strong solvents to
clean your tool.
STAY ALERT AND EXERCISE CONTROL.
■
Watch what you are doing and use common sense.
Do not operate tool when you are tired. Do not rush
operation of tool.
CHECK DAMAGED PARTS. Before further use of
■
the tool, a guard or any other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any
other conditions that may affect its operation. A guard
or any other part that is damaged should be properly
repaired or replaced by an authorised service centre.
DO NOT USE TOOL IF SWITCH DOES NOT TURN
■
IT ON AND OFF. Have defective switches replaced
by authorised service centre.
DO NOT OPERATE THIS TOOL WHILE UNDER
■
THE INFLUENCE OF DRUGS, ALCOHOL OR ANY
MEDICATION.
THE APPLIANCE IS NOT INTENDED FOR USE BY
■
YOUNG OR INFIRM PERSONS WITHOUT
SUPERVISION. YOUNG CHILDREN SHOULD BE
SUPERVISED TO ENSURE THAT THEY DO NOT
PLAY WITH THE APPLIANCE.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE
Due to continued product refinement policy, product
features and specifications can and will change without
notice. Check current features and specifications with
your retailer.
E I P NL S DK N FIN
English
OTHER SAFETY PRECAUTIONS FOR USING
SLIDING COMPOUND MITRE SAW
KEEP GUARDS IN PLACE AND IN WORKING
■
ORDER. Never wedge or tie lower blade guard open.
Check operation of lower blade guard before each
use. Do not operate if lower blade guard does not
close briskly over saw blade.
OUTDOOR USE EXTENSION CORDS. When tool is
■
used outdoors, use only extension cords intended for
use outdoors and so marked.
KEEP BLADES CLEAN AND SHARP. Sharp blades
■
minimize stalling and kickback.
KEEP HANDS AWAY FROM CUTTING AREA.
■
Keep hands away from blades. Do not reach
underneath work while blade is rotating. Do not
attempt to remove cut material when blade is moving.
WARNING: Blades coast after turning off.
INSPECT TOOL CORD PERIODICALLY. If damaged,
■
have it repaired by authorised service centre.
Stay constantly aware of cord location and keep it
well away from rotating blade.
USE RIP FENCE. Always use a fence or straight
■
edge guide when ripping.
BEFORE MAKING A CUT. Be sure the depth, bevel
■
and mitre adjustments are tight.
USE CORRECT BLADES. Do not use blades with
■
incorrect size holes. Never use blade washers or
bolts that are defective or incorrect. The maximum
blade capacity of your saw is 254 mm.
AVOID CUTTING NAILS. Inspect and remove all
■
nails from timber before cutting.
NEVER touch the blade or moving parts during use.
■
NEVER start the saw when the blade is in contact
■
with the workpiece.
LASER LIGHT. LASER RADIATION
Do not stare into beam.
Only turn laser beam on when tool is on
workpiece.
Class 2 laser product.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.
Laser type: Semiconductor
Laser class: 2
Wave length: 650 nm
Power supply: 3 V
Laser power: < 1 mW
14
GR H CZ RUS RO PL