Programming - Comunello Automation BORDER 400 Instrucciones De Uso Y De Instalacion

OBSTACLE DETECTION:
The electronic control unit is equipped with a "SENS" trimmer, completely
managed by the microprocessor, for adjustment of the opposing Force
required to detect the presence of an obstacle.
The adjustment can be made with a trip time from a minimum of 0.1
seconds to a maximum of 1 seconds
IMPORTANT: detection of an obstacle always causes a reversal of the
direction of movement.
FLASHING LIGHT:
The control unit features an output to control a 24 Vdc 4W max flashing
light. Operation of the flashing light depends on the movement of the motor.
OPERATION WITH TIMER:
The control unit allows a timer to be connected in place of the open – close
pushbutton.
E.g.: at 08.00 am the timer closes the contact and the control unit
commands an opening movement; at 06.00 pm the timer opens the
contact and the control unit commands a closing movement. From 08.00
am – 06.00 pm at the end of the opening cycle the control unit disables the
flashing light, automatic closing and the remotes.
BUFFER BATTERY:
The control unit is equipped with a built-in 27.4 V
to keep a full charge on the two 12V batteries connected in series. The
batteries allow the barrier to perform several complete open/close cycles
in emergency mode. The Flashing Light and LED strip output will operate
only for the first 4 seconds of the movement when mains power is absent.

10.5 PROGRAMMING

SEL key: selects the type of function to store; the selection is indicated by
blinking of the LED.
Press the key repeatedly to go to the required function. The selection
remains active for 10 seconds shown by blinking of the LED; when this
interval elapses the control unit returns to the original state.
SET key: programs the information in accordance with the function type
preselected with the SEL key.
IMPORTANT: The SET key function can be replaced by the remote if
programmed beforehand (CODE LED on).
MAIN MENU
The control unit is factory set to allow selection of several important functions.
L1 CODE TX
L2 MOTOR TIME Factory T. setting
L3 PAUSE TIME Without aut.close
L4 FORCE OPEN
L5 FORCE CLOSE
L6 SLOWING OPEN
L7 SLOWING CLOSE
LEV MENÙ
1. CODE (Remote control code):
Up to 120 remotes with different codes of either the fixed or rolling code
type can be saved on the control unit.
Programming.
The transmission code is programmed as follows: use the SEL key to
select blinking LED L1 and transmit the chosen code with the required
remote within 10 seconds; LED L1 will remain steady on to indicate that
programming has been completed.
If all 120 codes have been saved, repeating the programming operation will
cause all the programming LEDs to start blinking to signal that no further
codes can be saved.
Remote controls reset.
To delete all the previously saved remotes from the receiver, use SEL to
select LED L1, then press SET and hold it pressed for > 5 s. At the end
of this interval the LED will switch off for two seconds to confirm that the
procedure has been completed successfully.
Rule of the first saved Remote control:
When programming remotes the following rule is applied: if the first remote
to be saved is a rolling code type, the receiver will subsequently accept only
rolling code remotes, thus providing enhanced anti-intrusion security; if the
first remote to be saved is a fixed code type, the receiver will subsequently
accept both fixed code remotes and rolling code remotes.
22
COMUNELLO ®Copyright 2015 - All right reserved
battery charger
LED OFF LED ON
No code Code entered
Programmed time
With automatic close
Maximum Med – min set by speed
Maximum Med – min set by speed
Maximum Med – min set by slowing
Maximum Med – min set by slowing
ON
WARNING: Whenever you reset the remotes on the receiver, all the saved
remotes will be deleted and also the rule of the first saved remote control
will be reset to default.
2. MOTOR TIME (Barrier working time programming):
The control unit is factory set with a standard work profile. If the Operator
working time and slowing stages duration must be changed, reprogramming
must be performed with the barrier closed as follows: use the SEL key
to select blinking LED L2 and then press the SET key momentarily; the
Operator will start an Opening cycle; when the required slowdown starting
point is reached, press the SET key again; LED L2 will start blinking
more slowly and the Operator will decelerate; on reaching the required
position press SET to terminate the Opening cycle. When Opening cycle
time programming is completed, the Operator restarts immediately in the
Closing cycle: repeat the operations described above for the Closing cycle.
WARNING: The barrier working time function must be set with sensitivity
setting higher than 50% and at reduced speed.
3. PAUSE TIME (Automatic closing time programming 4 min. max.):
The control unit is factory set with automatic closing disabled. If you wish
to enable automatic closing proceed as follows: use the SEL key to select
blinking LED L3 and press the SET key momentarily; now wait for a time
equivalent to the required time; press the SET key again momentarily
and at the same time the automatic closing time will be saved and LED
L3 will remain steady on. If you wish to restore the initial condition (no
automatic closing) select blinking LED L3 and then press the SET key twice
consecutively in an interval of 2 seconds. The LED will switch off and the
operation will be completed.
4. FORCE OPEN (Selecting the Force profile in the Normal
Opening cycle):
The control unit allows you to define different operator Force profiles during
the Normal operating cycle in the Opening movement. In the factory set
configuration, operator Force during opening is set at the maximum level
"MAX" (i.e. identical to the setting selected using the SPEED trimmer with
LED L4 off); if you wish to change the profile to a medium level value "MED",
proceed as follows: use the SEL key to select blinking LED L4 and press the
SET key; at the same time LED L4 becomes steady on and programming
will be completed. If you wish to change the profile to a Minimum value
"MIN" repeat the operation described above, pressing the SEL key twice
(LED L4 will blink rapidly) rather than once. Repeat the procedure if you wish
to restore the initial configuration.
5. FORCE CLOSE (Selecting the Force profile in the Normal
Closing cycle):
The control unit allows you to define different operator Force profiles during
the Normal operating cycle in the Closing movement. In the factory set
configuration, operator Force during closing is set at the maximum level
"MAX" (i.e. identical to the setting selected using the SPEED trimmer with
LED L5 off); if you wish to change the profile to a medium level value "MED"
proceed as follows: use the SEL key to select blinking LED L5 and press the
SET key; at the same time LED L5 becomes steady on and programming
will be completed. If you wish to change the profile to a Minimum value
"MIN" repeat the operation described above, pressing the SEL key twice
(LED L5 will blink rapidly) rather than once. Repeat the procedure if you wish
to restore the initial configuration.
6. SLOWING OPEN (Selecting the Force profile in the Opening
Slowdown cycle):
The control unit allows you to define different operator Force profiles during
the Slowdown operating cycle in the Opening movement. In the factory
set configuration, operator Force during the opening slowdown stage is
set at the maximum level "MAX" (i.e. identical to the setting selected using
the SLOWING menù with LED L6 off); if you wish to change the profile to a
medium level value "MED" proceed as follows: use the SEL key to select
blinking LED L6 and press the SET key; at the same time LED L6 becomes
steady on and programming will be completed. If you wish to change the
profile to a Minimum value "MIN" repeat the operation described above,
pressing the SEL key twice (LED L6 will blink rapidly) rather than once.
Repeat the procedure if you wish to restore the initial configuration.
7. SLOWING CLOSE (Selecting the Force profile in the Closing
Slowdown cycle):
The control unit allows you to define different operator Force profiles during
the Slowdown operating cycle in the Closing movement. In the factory set
configuration, operator Force during the closing slowdown stage is set at
the maximum level "MAX" (i.e. identical to the setting selected using the