Product Characteristics; Technical Parameters; Safety Instructions - YATO YT-58962 Manual De Instrucciones

PRODUCT CHARACTERISTICS

The chain lever hoist is used for lifting loads by with a hook attached to the chain. You can not use the hoist to move a load in the
direction other than up and down. You cannot use the hoist a pulling hoist mechanism which is set permanently. Correct, reliable
and safe operation of the device is dependent on its proper use, therefore:
Before beginning your work, you should read the manual and keep it around.
For any damage caused by failure to comply with safety regulations and instructions of this manual, the supplier does not accept
any liability.
EQUIPMENT OF THE PRODUCT
The product is supplied in a complete state and requires no assembly.

TECHNICAL PARAMETERS

Parameter
Catalogue No
Lifting height:
Lifting capacity
A test load for work
The force which is needed to lift maximum load
The number of cargo chains
Dimensions of the chain link
A
B
C
Dimension D
H
L
K
Net weight
Weight increase for each additional meter of height lifting

SAFETY INSTRUCTIONS

The hoist is a mechanical device running under heavy load. When operating it you should observe basic safety rules.
The hoist is not intended to move people or animals.
You should check the chain condition. Before starting work, check that the chain is not tangled, twisted, worn out or damaged. Do
not use the hoist in case when the chain is entangled. First untangle the tangled links. When you notice that the links are distorted
or worn out (threadbared) any further work is prohibited. In the case of detection of poor condition of the chain, any further work is
prohibited. The chain should be replaced with a new one. To do this, you should submit the hoist to an authorized service center.
During operation of the hoist no chain may touch any point of foreign objects.
You should do not attach the moving load by belting it by a chain and hooking the hook on the chain.
Do not overload the hoist. Pay attention to the information about the maximum working load, which is placed on the product
nameplate.
During the prolonged lowering of loads there is a risk of overheating the brake system.
The product is not intended for use in an atmosphere with an increased risk of explosion or atmosphere with increased risk of
corrosion.
Do not leave an unattended lifted load. Children and people, who are untrained to operate the device are not allowed be present
near the device.
Do not raise the load is too high or lower it too low.
You should make sure, that all the components (such as hooks, catches, etc.), to which the hoist will be attached, will withstand
the load occurring during operation of the hoist.
It is forbidden to use the hoist for uses other than lifting loads.
It is required that during the hoist operation, its operators watch all the time moved load. Particular attention should be paid, that
on the way of moved load there will not be any people or animals. It is forbidden to move or stay under the load when it is moved.
it is forbidden to allow swinging of the moved load.
Do not use excessive force when lifting loads, especially not jerk the lever. If the load is lifted with resistance, discontinue the
O R I G I N A L
6
GB
Unit
YT-58962
[m] 1.5
[thousand. kg] 0.75
[kN] 11.2
[N] 140
1
[mm] 6 x 18
[mm] 145
[mm] 86
[mm] 134
[mm] 38
[mm] 340
[mm] 285
[mm] 27
[kg] 9.5
[kg] 0,8
I N S T R U C T I O N S
Value
YT-58964 YT-58966 YT-58967
1,5 1,5
1,5 3
22.5 45
220 320
1 1
8 x 24 10 x 30
175 195
100 115
150 190
48 50
380 490
410 410
36 38
11.5 18.5
1,4 2.2
YT-58968
1,5 1,5
6 9
75 112.5
340 360
2 3
10 x 30 10 x 30
195 195
115 115
242 307
65 81
620 700
410 410
48 54
27.5 46
4,4 6.6