Osram OPTOTRONIC OTi QBM 20/220-240/500 NFC I Manual De Instrucciones página 2

OTi QBM 20/220-240/500 NFC I | OTi QBM 30/220-240/700 NFC I | OTi QBM 40/220-240/1A0 NFC I
21)
Position
Input /PRI
24)
A or B
one cable
Input /PRI
26)
A and B
two cables
C Output / SEC
D Output / SEC
*Safety information for mains through wiring: Cable temperature in the cable clamp compartment de-
pends on cable type, ambient temperature and through wiring current. Therefore through wiring current
is limited. 2-wire connector for solid earthing conductors, e.g. WAGO 2273-202, is recommended.

Installing and operating information:
Connect only LED load type. LED module will be switched off when output volt-
age is outside the voltage range given on the driver.
Wiring information (see fig. A):
Do not connect the outputs of two or more units. Output current adjustment
via software programming using Near Field Communication (NFC) in mains
off mode only. Unit is permanently damaged if mains is applied to the terminals
21/22. Lines 21/22 max. 2 m whole length excl. modules. Bluetooth network
reset: (1) Power off device and disconnect from mains, apply short circuit
between LED+ and LED-, (2) connect device to mains and power on for at
least 2 seconds, (3) power off device, disconnect from mains and remove short
circuit. Reset completed.
Emergency Lighting:
This LED power supply complies with EN 61347-2-13 Annex J and is suitable for
emergency lighting fixtures according to EN 60598-2-22.
1) Qualified Bluetooth mesh compact LED driver for independent installation;
2) Constant current LED Power Supply; 3) t c point; 4) Made in Bulgaria by
OSRAM; 5) picture only for reference, valid print on product; 6) Radio fre-
quency; 7) Wireless protocol; 8) Qualified Bluetooth mesh; 9) Wireless range;
10) 10 m line of sight; 11) Mains; 12) Input; 13) Output; 14) Through looping;
15) Year; 16) Week; 17) Mounting hint for proper radio connectivity. By in-
tegrating the device into a casing the wireless range could be affected, in
particular by metal surfaces. Therefore, the wireless range needs to be
verified after integration. 18) Do not place any mains voltage or LED supply
wires within or close to this area. 19) Recommended minimal distance to
metal parts. 20) Placement of integrated radio transmitter antenna; 21) Po-
sition; 22) Cable types (tested acc. to EN 60598-1); 23) Remark; 24) A or B;
25) one cable; 26) A and B; 27) two cables; 28) Mains through wiring current
≤10A; 29) Safety information for mains through wiring: Cable temperature
in the cable clamp compartment depends on cable type, ambient tempera-
ture and through wiring current. Therefore through wiring current is limited.
2-wire connector for solid earthing conductors, e.g. WAGO 2273-202, is
recommended.
2
Cable type (tested acc. to EN 60598-1)
• NYM-J 3x1.5
• H05VV-F 3x1.5
25)
• NHXMH-J 3x1.5
• NYM-J 3x1.5
• H05VV-F 3x1.5
27)
• NHXMH-J 3x1.5
• Style 21073
• Style 21520
• H03VVH2-F 2x0.75
• H03VV-F 2x0.5
• H05VV-F 2x1.0
• H05VV-F 2x1.5
The device can be put into operation using the OSRAM HubSense Commis-
sioning Tool (https://platform.hubsense.eu), subject to prior acceptance of the
Terms of Use and the Privacy Policy. OSRAM may terminate or suspend the use
of the HubSense Commissioning Tool at any time and for any or no reason in
its sole discretion, even if access and use is continued to be allowed to others.
The device has passed successfully the SILVAIR Testing process.
The device complies with Bluetooth mesh Standard v1.0. It can also be used
in 3rd party Bluetooth mesh network, that complies with this standard and that
supports the mesh models of this device, and with certain 3rd party commis-
sioning tools, that support the mesh models of this device. In order to ensure
correct interoperability a verification with the 3rd party network components
and the 3rd party commissioning tool is necessary in advance. Please contact
OSRAM (support@hubsense.eu) to receive the actual list of supported models
for this device.
OSRAM shall have no liability for any 3rd party commissioning tool and does
not make any representations, express or implied, about the availability and/or
performance of such commissioning tool.
OSRAM shall have no liability for and does not make any representations, express
or implied, about the connectivity of OSRAM QBM products with any other
products, that have passed the SILVAIR Testing process.
Hereby OSRAM GmbH declares that the radio equipment types OTi QBM 20
NFC I, OTi QBM 30 NFC I and OTi QBM 40 NFC I are in compliance with Direc-
tive 2014/ 53/ EU. The full text of the EU declaration of conformity is available at
the following internet address: www. osram. com/ot-indoor-ce.
NFC frequency range: 13 553 - 13 567 kHz
Bluetooth frequency range: 2402 - 2480 MHz
Max HF output power (EIRP) of the product: 4 dBm
Technical support: www.osram.com, +49 (0)89-6213-6000
22) 23)
Remark
Mains through wiring
current ≤10A*
28)
29)