Descargar Imprimir esta página

EdilKamin ALPEN Instalacion Uso Mantenimiento página 38

Ocultar thumbs Ver también para ALPEN:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 68
Variation feeding pellets (ONLY AFTER SUGGESTED
BY DEALER)
Press and hold the "M" key on the remote control for two se-
conds. Scroll through the display instructions using the "+"
and "–" keys, to the description "ADJ-PELLET". By con-
rming this function using the menu key you can adjust the
supply of pellets,
by reducing the set value, you decrease the supply of pellets,
increasing the set value increases the supply of pellets. This
function can be useful in the event that one changes the type of
pellets used, no longer using those for which the boiler-stove
was calibrated, thus necessitating an adjustment of the load
setting.
Should this correction not suf ce, contact the Edilkamin-
authorised Dealer, to establish the new operating axis.
Notes on ame variability:
ame depend on the type of pellets used, as well as on normal
variation of solid fuel ames and on the periodic cleaning of
the crucible the boiler-stove automatically carries out
(Note: This does NOT replace the necessity cold vacuuming by
the user prior to start up).
View Kg pellets consumed
the "kg pellets consumed" menu displays the total stove con-
sumption of heating pellets.
Environmental temperature control
this comfortable and simple adjustment feature, as standard in
this line of products, allows you to manage the stove power
based on the environmental temperature.
After activating the "Comfort Clima" function from the para-
meters menu (ask the technical assistance centre - TAC), press
the SET button brie y a couple of times to switch from classic
"Modulate_Power" mode to "Comfort Clima" mode; then
select the desired mode from the display.
Modulate power mode
the stove modulates its power by following the output tempera-
ture set by the user.
Comfort Clima mode
the stove modulates its power by following the output tempe-
rature set by the user. You can also use the remote control as a
room thermostat: on reaching the set temperature the stove will
go to minimum power.
Setting the environmental temperature
In "Comfort Clima" mode, by pressing the +/- buttons on the
synoptic panel or on the remote control, you can set the display
to the desired environmental temperature.
-At environmental temperatures below the set temperature, the
stove modulates power normally to reach the set output.
-With environmental temperature reached (+2°C), the stove
goes to minimum power.
INSTRUCTIONS FOR USE
Any changes in the state of the
The environmental temperature is transmitted from the remote
control; the remote control transmitter must be visually aligned
with the receiver of the synoptic panel
If the remote control is incorrectly positioned, it cannot send
its recorded temperature. The stove therefore independently
decides to operate at minimum power and continues thus until
the connection with the remote is restored
Temperature control with external thermostat
another temperature control system is available as an alterna-
tive to the remote control. You can in fact connect the thermo-
stat serial port to your home thermostat or any (clean output
contact) easily available one
The stove will automatically recognise the connection with the
thermostat serial port under the following conditions:
With environmental temperature lower than the thermostat
setting (contact closed), the stove modulates power normally to
reach the set temperature
-With environmental temperature reached by the thermostat
(contact open), the stove goes to minimum power
Temperature
Con guration
provided by the
remote control
"Comfort
Clima"
ON
parameter
"SONDA IR"
ON
parameter
Connection to
NO
serial port
no connection
- 38
-
Temperature
provided by
No adjustment
external
(factory setting)
environmental
thermostat
ON
ON
OFF
ON
Yes
NO
with blue
no connection
serial cable

Publicidad

loading

Este manual también es adecuado para:

AndeFujiUral