■
Changing the set temperature
Push the "TEMP.
" buttons.
1
Push
to increase the temperature, and
decrease the temperature. (The set temperature
cannot be changed in the fan mode.)
NOTE
When cooling
Running starts in approximately 1 minute.
When heating [For Heat-pump model only]
• The air conditioner may continue running in the fan
mode for about 30 seconds after stopping heating.
• The heated air comes out after a 3 to 5 minutes of
pre-heating with the indoor fan kept turned off. (The
pre-heat indicator
is displayed on the remote
controller.)
• The fan speed becomes extremely low when the
room temperature has reached the set temperature.
However, for concealed duct high static types, the
fan speed does not change after the temperature has
reached to the set temperature.
71-EN
1117102201-2_EN.indd 36
1117102201-2_EN.indd 36
■
Power save operation
to
Displayed during
Power save
operation
TEMP.
ON / OFF
TIMER SET
FAN
MODE
Save button
TIME
SAVE
VENT
FILTER
RESET
TEST
SET
CL
SWING/FIX
UNIT LOUVER
1
Push the
button during operation.
• Power save operation is activated.
•
is appeared.
2
Push
button to deactivate Power save
operation.
•
is disappeared.
NOTE
• Capability of the air conditioner is saved during the
Power save operation. The room may not become cool
or warm enough.
• Power save operation will not be deactivated by stop
operation, change operation mode or turn off the power
switch.
5
Timer operation
Select a timer type from the following three: (Max. 168 hours)
OFF timer :
Stops running after the specifi ed period.
Repeat-OFF timer :
Stops running after the specifi ed period every time you use the air conditioner.
ON timer :
Starts running after the specifi ed period.
■
Setting the timer
1
3
1
Push the
button.
Each time you push the button, the timer mode
and indication change in the following order
Off
Off
(Off timer)
(Repeat Off timer)
(On timer)
No indication (Timer
function is deactivated)
•
and the time indicator blink.
2
Push the
buttons to set the period of
time until the timer actions.
• The time setting increases in 0.5-hour (30-
minute) increments each time you push
The setting increases in 1-hour increments if
it is over 1d (24 hours). The maximum is 7d
(168 hours). On the remote controller, settings
between 0.5h and 23.5h (*1) are displayed as
is. If it is over 24 hours (*2), the days and hours
appear.
• The time setting decreases in 0.5-hour (30-
minute) decrements (0.5 hours to 23.5 hours) or
1-hour decrements (24 hours to 168 hours) each
time you push
.
Example of remote controller display
• 23.5 hours (*
1
)
– 36 –
2
• 34 hours (*2)
indicates 1 day
(24 hours).
indicates 10 hours.
(Total: 34 hours)
On
3
SET
Push the
button.
•
disappears, the time indication is
displayed, and
or
display fl ashes.
(When using the ON timer, all indications other
than the time and
turn off.)
■
Cancelling the timer
.
1
SET
Push the
button.
The timer indicator disappears.
NOTE
• When using Repeat OFF timer, pushing the
button after stopping by the timer starts running again
and the timer will stop the running again after the
specifi ed period.
• When using OFF timer, the timer indication temporarily
disappears for about 5 seconds by pushing the
button. This occurs due to the processing in the remote
controller, and is not a malfunction.
Days
Hours
72-EN
6/30/2559 BE 15:41
6/30/2559 BE 15:41