Extended Menu - Seav BeWeather Serie Manual De Instrucciones

Wind safety threshold selection from 5 to 40 km/h
The control unit comes with a default wind safety threshold setting of 25 km/h (WIND
LED OFF).
The wind safety threshold may be programmed in the following way: use the SEL key to
navigate to WIND LED, then press the SET key to start the programming procedure: At the
same time the WIND LED will begin to double-flash (each double-flash of the WIND LED
corresponds to an increase of 5 km/h); press the SET key once the desired threshold has
been reached – at this moment, the selected value will be stored and the WIND LED will
remain lit ((for example: 5 WIND LED double-flashes = 25 km/h).
The operation may be repeated if a mistake is made during programming.
4) SUN SENSOR ( Sun Sensor ON/OFF )
Enabling the Sun Sensor
The control unit comes with the Sun Sensor disabled (SUN SENSOR LED OFF).
The Sun Sensor may be enabled in the following way: press the SEL key until the SUN
SENSOR LED flashes, then press the SET key briefly; at this moment the SUN SENSOR
LED remains lit and the Sun Sensor will be enabled. Repeat the operation to disable the
Sun Sensor.
Enabling the Sun Sensor using a 3-button radio control (BeFree x3 - X6):
The Sun Sensor may be enabled in the following way: hold down the (+) key on the radio
control that was programmed previously for 5 seconds; at the same time the control unit will
cause the shutter to move Up/Down for 1 second to confirm that the Sun Sensor has been
enabled, and the SUN SENSOR LED will remain lit. Repeat the operation to disable the Sun
Sensor by following the same procedure, but instead holding down the (-) key for 5 seconds.
5) RAIN SENSOR ( Rain Sensor ON/OFF )
Disabling the Rain Sensor
The control unit comes with the Rain Sensor enabled (RAIN SENSOR LED ON).
The Rain Sensor may be disabled in the following way: press the SEL key until the RAIN
SENSOR LED flashes, then press the SET key briefly; at this moment the RAIN SENSOR
LED switches off and the Rain Sensor will be disabled. You can repeat the operation to
enable the Rain Sensor.

EXTENDED MENU

The control unit is supplied by the manufacturer with the option of selecting only the
functions listed in the main menu.
To enable the functions of the extended menu proceed as follows: press the SET key
and hold for 5 seconds; the SUN, RAIN and R. HEAT LEDs will flash and the user has 30
seconds within which to select the functions of the extended menu using the SEL and SET
keys. After another 30 seconds the control unit returns to the main menu.
—————————— EXTENDED MENU
Reference LED LED Off
A) CODE remote PGM = OFF
B) T. MOT. Aut. movement lock = OFF
C) WIND SPEED Safety upward = OFF
D) SUN SENSOR RAIN inversion = OFF
E) RAIN SENSOR Aut. movements 5 min.
F) SUN
G) RAIN
H) R. HEAT
A) CODE (Remote programming of radio control) :
The control unit allows the transmission code to be programmed by remote, without using
the SEL key.
To programme the transmission code remotely, proceed as follows: send the radio control
code continuously for more than 10 seconds and the control unit will enter the program-
ming mode as described above for the CODE LED in the main menu.
The control unit is supplied by the manufacturer with remote programming of the trans-
mission code not enabled; to enable the function proceed as follows: check that the
extended menu is enabled (SUN, RAIN and R. HEAT LEDs flash), using the "SEL" key
navigate to CODE LED when flashing and press the "SET" key: the CODE LED lights up
permanently and programming is completed. Repeat the operation to restore the previous
configuration.
B) T. MOT. (Automatic movement lock) :
The control unit enables the prevention of Automatic movements (Up / Down sun blind
movements on the Sun Sensor command or Automatic Sensors function), so that if a Stop
command is sent from a radio control during the movement, the control unit momentarily
locks the Automatic movements until a new Up or Down command is sent. The control
unit is supplied by the manufacturer with the Automatic Movement Lock disabled; to
enable the function proceed as follows: check that the extended menu is enabled (SUN,
RAIN and R. HEAT LEDs flash), using the "SEL" key navigate to T. MOT. LED when flash-
ing and press the "SET" key: the T. MOT. LED lights up permanently and programming is
completed. Repeat the operation to restore the previous configuration.
C) WIND ( Safety Upward Movement ) :
The control unit is supplied by the manufacturer with the Safety upward movement func-
tion disabled; if you wish to enable the function, in such a way that after 12 hours of
inactivity of the Wind Sensor the control unit automatically control the safety upward
15
————————————
LED On
remote PGM = ON
Aut. movement lock = ON
Safety upward = ON
RAIN inversion = ON
Aut. Movements 10 min.
Flashing beacon ON/OFF
Flashing beacon ON/OFF
Flashing beacon ON/OFF