Tabla de contenido
Publicidad
Technical specifications
Wattage:
100 watts max./E 27 or 2 x 40 W max./G9 (L 260 / 261 S: G9)
Voltage:
230 – 240 V, 50 Hz
Angle of coverage:
240° with 180° angle of aperture
Sensor reach:
max. 12 m
Time setting:
5 sec. – 15 min.
Twilight setting:
2 – 2000 lux
Brightness control:
(L 262 – 265 S)
0 – 50% (Watt-o-matic)
Manual override:
selectable (4 hours):
Provided switch is connected in mains supply lead
Enclosure:
IP 44
Temperature ranging from:
- 20° C to + 50° C
Functions
,
,
The SensorLight can be put into service after mount-
ing the sensor unit and connecting the light to the
mains power supply.
Twilight setting
(response threshold)
(factory setting:
daylight operation 2000 lux)
Switch-off delay
(time setting)
(factory setting: 5 sec.)
L 262 – L 265 S:
Brightness control
(Watt-o-matic)
(factory setting:
dimmer off: 0%)
Sensor response threshold can be infinitely varied
from 2 – 2000 lux.
Control dial set to
= daylight operation
approx. 2000 lux.
Control dial set to
= twilight operation
approx. 2 lux. To adjust the detection zone in daylight,
set control dial to
(daylight operation).
Light ON duration can be infinitely varied from
5 sec. to 15 min.
Control dial set to – = shortest time
Control dial set to + = longest time (15 min.)
It is recommended to select the shortest time
– when adjusting the detection zone
Light output can be infinitely adjusted up to 50 % of
maximum power when set to stay on all the time.
This means: when the light is set to stay on all
the time, it will only switch from, say, 20 watts to
max-imum light output when movement occurs in
the sensor detection zone.
PK Elektronik Vertriebs GmbH, E-Mail: info@pkelektronik.com, Internet: www.pkelektronik.com
- 10 -
Manual override function
If a mains switch is installed in the mains supply lead,
the light is capable of the following functions in addi-
tion to the simple ON/OFF function:
Sensor operation
1) Switch light ON (when light is OFF):
Switch 1 x OFF and ON.
Light stays on for the period selected.
2) Switch light OFF (when light is ON):
Switch 1 x OFF and ON.
The light goes out or switches over to sensor mode.
Soft light start
The sensor light features a soft light start function.
This means that when turned on, the light is not
switched directly to maximum output but gradually
Reach setting/adjustment
At an assumed installation height of 2 m, the sensor
has a maximum reach of 12 m. The detection zone
can be optimised to suit needs. The shrouds provided
are used for blanking off any number of lens seg-
ments or to shorten reach as required. This prevents
the light from being activated unintentionally, e.g. by
cars, passers-by etc. and allows you to target danger
spots. The shrouds can be divided or cut with a pair
of scissors along the vertical and horizontal grooves.
Operation/Maintenance
The sensor light is suitable for switching light on
automatically. Weather conditions may affect the way
the sensor light works. Strong gusts of wind, snow,
rain or hail may cause the light to come on when it is
not wanted because the sensor is unable to distin-
guish sudden changes of temperature from sources
of heat. The detector lens may be cleaned with a
damp cloth if it gets dirty (do not use cleaning
agents).
Declaration of conformity
This product complies with
- Low Voltage Directive 2006/95/EC
- EMC Directive 2004/108/EC
Manual override
1) Switch ON manual override:
Switch ON and OFF twice. The light will stay ON for
4 hours (red LED lights up behind the lens). Then it
returns automatically to sensor mode (red LED off).
2) Deactivate manual override:
Switch ON and OFF once. Light goes out or changes
over to sensor mode.
Important:
The switch should be actuated in rapid succession
(in the 0.5 – 1 sec. range).
builds up brightness to 100 % within the space of a
second. Brightness is also gradually reduced when
the light is switched OFF.
After removing the decorative ring, the shrouds can
be clipped on at the top of the sensor lens. The dec-
orative ring must now be pushed back on to hold the
shrouds firmly in place.
Precision targeting can be achieved by turning the
sensor housing through ± 80°
.
Note: (L 260 / L 261 S)
Stainless steel should be cleaned at regular intervals
(about every 3 months) with a standard stainless steel
cleaner. If it is not cleaned, corrosion may
occur on the surface (flash rust). Excellent
results are achieved with SIDOL CERAN &
steel cleaner from Henkel when applied
along the grain of the stainless steel
brushed finish. Do not use chlorine-
based cleaning products.
- 11 -
Publicidad
Tabla de contenido
