Technical Specification - Rapid 2000 Manual Del Usuario

power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
HOT AIR TOOL SAFETY
WARNINGS
WARNING: T
stand when not in use.
A
fire may result if the appliance is not used with
care, therefore
– be careful when using the appliance in places
where there are combustible materials;
– do not apply to the same place for a long time;
– do not use in presence of an explosive
atmosphere;
– be aware that heat may be conducted to com-
bustible materials that are out of sight;
– place the appliance on its stand after use and
allow it to cool down before storage;
– do not leave the appliance unattended when it
is switched on.
I
- f the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid
a hazard.

TECHNICAL SPECIFICATION

Rapid Thermal 1600
Rapid Accelerator 2000
Model
Rapid Regulator 2000
Rapid Digit 2000
Voltage 230 V., 50Hz
Thermal 1600W
Power
Accelerator, Regulator, Digit 2000W
FEATURES
FIGURE 1 - 5
Nozzle
Handle
6
his tool must be placed on its
Hanger
Switch OFF / Speed 1 / 2. Reduced power/
temperature on speed 1
Temperature control buttons + up – down, DIGIT
2000. Figure 2
LCD display, Digit 2000
Heat guard, Digit 2000
Temperature control dial + up – down, Regulator
2000. Figure 4
Stand for vertical operation with free hands or
storage, Digit 2000. Figure 5
WARNING!! Read all safety warnings and all
instructions.
Save all warnings and instructions for future
reference.
Ensure the power switch is in the OFF position before
plugging into the electrical outlet.
Set the power switch/temperature control to the desired
speed and temperature. Let the tool run until it reaches
operating temperature.
Digit 2000 has a separate stand to be used on a flat
level surface.
With the stand the tool can be used in a vertical position
with both hands free for work.
Keep hands away from the immediate nozzle area, it's hot.
PAINT AND VARNISH REMOVAL
Never use the heat gun in combination with chemical
strippers.
WARNING! LEAD PAINT FUMES ARE VERY
HARMFUL. ALWAYS PROVIDE ADEQUATE
VENTILATION WHILE WORKING INDOORS.
Removal of paint and varnish requires some practice but
some simple working techniques are described here. Test
on a small area of paint before moving on to larger areas.
Turn on the tool and allow it to reach working
temperature. Hold the nozzle 70 to 100 mm from the
paint to be removed. After a short time the paint will
soften and begin to bubble. Do not overheat the paint, as
this will cause burning and make the paint more difficult
to remove.
Begin scraping the paint off. Use accessory scrapers.
Scrape with smooth, even strokes, warming the surface
in front of the scraper by moving the tool slightly from
side to side. If paint is warmed properly, even thick layers
can be removed in a single pass. Scrape the paint as
soon as it softens since it will quickly harden again.
Figure 8
Clean the edge of scraper blade often.
Shaped or profiled surface can be stripped with a wire
brush after softening with the hot air tool.
Protect surfaces NOT to be heated with non flammable
material, Figure 7. Never concentrate tool's heat on a
USAGE