Error Displays; Specifications - Clarion CZ702E Manual De Instrucciones Y De Instalación

USB Devices
Problem Cause
The USB device has been
USB device cannot
inserted with wrong direction.
be inserted.
The USB connector is broken.
The USB device is damaged.
USB device is not
recognized.
Connectors are loose.
No sound heard with
No MP3/WMA file is stored in the
the display "No File"
USB device.
shown.
Sound skips or is MP3/WMA files are not encoded
noisy. properly.
Bluetooth
Problem Cause
The device does not support the
Cannot pair the
profiles required for the system.
Bluetooth enabled
device with the car
The Bluetooth function of the
audio system.
device is not enabled.
The internal microphone gain is
The audio quality
not set correctly.
is poor after
connection with a
The external microphone is not set
Bluetooth-enabled
correctly nor properly positioned.
device.

7. ERROR DISPLAYS

If an error occurs, one of the following displays is displayed.
Take the measures described below to solve the problem.
Display Cause
Disc is inserted incorrectly.
ERROR 3
The disc format is not supported.
ERROR 5 This is a failure of deck's mechanism.
If an error display other than the ones described above appears, press the
problem persists, turn off the power and consult your store of purchase.
[RESET]
* When the button is pressed, frequencies of radio stations, titles, etc. stored in
memory are cleared.
Measure
Reversing the connection direction of the USB
device, try it again.
Replace with a new USB device.
Disconnect the USB device and reconnect. If the
device is still not recognized, try replacing with a
different USB device.
Store these files properly in the USB device.
Use MP3/WMA files encoded properly.
Measure
Use another device to connect.
Refer to the user manual of the device for how to
enable the function.
Adjust the gain of the internal microphone in
System Setup.
Adjust the gain and position of the external
microphone.
For example, stick the microphone onto the
dashboard so it is close to the driver.
Measure
Eject the disc then reload it properly.
Try another disc.
Consult your store of purchase.
[RESET]
button. If the

8. SPECIFICATIONS

FM Tuner
Frequency range: 87.5-108.0MHz
Usable sensitivity: 8dBf
Frequency response: 30Hz-15kHz
Stereo separation: 30dB(1kHz)
Signal/noise ratio: >55dB
MW Tuner
Frequency range: 531- 1602kHz
Usable sensitivity (S/N=20dB): 30dBμ
LW Tuner
Frequency range: 153-279kHz
Usable sensitivity (S/N=20dB): 34dBμ
CD Player
System: Disc digital audio system
Frequency response: 20Hz-20kHz
Signal/noise ratio: >94dB
Total harmonic distortion: Less than 0.1% (1kHz)
Channel separation: >60dB
MP3/WMA mode
MP3 sampling rate: 8 kHz to 48 kHz
MP3 bit rate: 8 kbps to 320 kbps / VBR
WMA bit rate: 8 kbps to 320 kbps
Logical format: ISO9660 level 1,2
Joliet file system
USB
Specification: USB 1.0/2.0
Playable audio format:
MP3(.mp3): MPEG 1/2/Audio Layer-3
WMA(.wma): Ver 7/8/9.1/9.2
Bluetooth
Specification: Bluetooth Ver. 2.0+EDR
Profile:
HFP (Hands-free Profile)
PBAP(Phone Book Access Profile)
A2DP (Advanced Audio Distribution Profile)
AVRCP (AV Remote Control Profile)
Send/Receive Sensitivity: Class 2
Audio Amplifier
Maximum power output:
200W (50W x 4)
Speaker impedance: 4 (4 to 8 allowable)
Input
Audio input sensitivity:
High: 320mV (at 2.5V output)
Mid: 650mV (at 2.5V output)
Low: 1.3V (at 2.5V output)
(input impedance 10 k or greater)
Aux-in level: ≤2V
General
Power supply voltage:
14.4VDC (10.8 to 15.6V allowable),
negative ground
Pre-Amp output voltage:
5.0V (CD play mode: 1kHz, 0dB, 10k load)
Fuse: 15A
Dimensions of the Main Unit:
188mm Width × 58mm Height × 190mm Depth
Weight of the Main Unit: 1.40kg
Dimensions of the Remote Control unit:
43mm Width × 11mm Height × 113mm Depth
Weight of the Remote Control Unit:
36g (including battery)
178mm 50mm
46mm
170mm
58mm
188mm
Note:
• Specifications and design are subject to change
without notice for further improvement.
CZ702E
15