Radio Operations - Clarion CZ702E Manual De Instrucciones Y De Instalación

Audio Setup
SLOP: -6 / -12DB
- REAR SPK: PHASE NOR/PHASE REV
• SP GAIN
HIGH: -20-----0DB
MID: -20-----0DB
REAR: -20-----0DB
3. When speaker system is "3WAY".
• TIME ALIGNMENT
HIGH L/R: 0----501.4cm
MID L/R: 0----501.4cm
SW L/R: 0----501.4cm
• 3W XOVER
- HIGH HPF
CUT: 25HZ / 31.5HZ / 40HZ / 50HZ / 63HZ
/ 80HZ / 100HZ / 125HZ / 160HZ / 200HZ /
250HZ / 315HZ / 400HZ / 500HZ / 630HZ /
800HZ / 1K / 1.25K / 1.6K / 2K / 2.5K / 3.15K
/ 4K / 5K / 6.3K / 8K / 10.0K / 12.5K / 16K /
20K / THROUGH
SLOP: -6 / -12DB
- HIGH SPK: PHASE NOR/PHASE REV
- MID LPF
CUT: 630HZ / 800HZ / 1K / 1.25K / 1.6K
/ 2K / 2.5K / 3.15K / 4K / 5K / 6.3K / 8K /
10.0K / THROUGH
SLOP: -6 / -12DB
- MID HPF
CUT: 25HZ / 31.5HZ / 40HZ / 50HZ / 63HZ
/ 80HZ / 100HZ / 125HZ / 160HZ / 200HZ /
250HZ / 315HZ / 400HZ / 500HZ / 630HZ /
800HZ / 1K / 1.25K / 1.6K / 2K / 2.5K / 3.15K
/ 4K / 5K / 6.3K / 8K / 10.0K / THROUGH
SLOP: -6 / -12DB
- MID SPK: PHASE NOR/PHASE REV
- SW LPH
CUT: 25HZ / 31.5HZ / 40HZ / 50HZ / 63HZ
/ 80HZ / 100HZ / 125HZ / 160HZ / 200HZ /
250HZ / 315HZ / 400HZ / 500HZ / 630HZ /
800HZ / 1K / 1.25K / 1.6K / 2K / 2.5K / 3.15K
/ 4K / 5K / 6.3K / 8K / 10.0K / THROUGH
SLOP: -6 / -12DB
- SW HPF
CUT: THROUGH / 16HZ / 20HZ / 25HZ
/ 31.5HZ / 40HZ / 50HZ / 63HZ / 80HZ /
100HZ/ 125HZ / 160HZ / 200HZ /250HZ
SLOP: -6 / -12DB
- SW SPK: PHASE NOR/PHASE REV
• SP GAIN
HIGH: -20-----0DB
MID: -20-----0DB
S-WOOFER: -20-----0DB
STORE/RECALL (NORMAL, 2WAY and
3WAY mode)
Rotate the [VOLUME] knob to choose "STORE
/ RECALL". Press the [VOLUME] knob to
confirm.
• STORE
Rotate the [VOLUME] knob to select a
position among "MEMORY 1, 2 and 3". Then
press and hold the [VOLUME] knob to store.
• RECALL
Rotate the [VOLUME] knob to select a
position among "MEMORY 1, 2 and 3". Then
press the [VOLUME] knob to recall.
Adjusting Sound Mode
Short-press the [ ] button to enter sound
effect setting mode. First press shows current
EQ. Rotate the [VOLUME] knob to change the
BEAT EQ in this order:
OFF -> B-BOOST -> IMPACT -> EXCITE ->
CUSTOM
Rotate the [VOLUME] knob to choose the
CUSTOM, and press the [VOLUME] knob, then
press [ ] or [ ] button to select it including:
BAND 1 G -> BAND 1 F -> BAND 1 Q -> BAND
2 G -> BAND 2 F -> BAND 2 Q -> BAND 3 G ->
BAND 3 F -> BAND 3 Q -> BAND 4 G -> BAND
4 F -> BAND 4 Q -> BAND 5 G -> BAND 5 F ->
BAND 5 Q, rotate the [VOLUME] knob to select
a value.
BAND 1/2/3/4/5 G: (-12) - (+12)
BAND 1/2/3/4/5 F: 20HZ - 20.0K, THROUGH
BAND 1/2/3/4/5 Q: 1, 3, 5, 7, 20
Press the [ ] button, then press [
or [ ] button to select USER preset including:
BALANCE -> FADER(NORMAL, 2 WAY mode)
-> SUBW VOL(Subwoofer Volume)(NORMAL,
3 WAY mode), rotate the [VOLUME] knob to
select a value.
BALANCE: LEFT 1-12->CENTER->RIGHT
1-12
FADER: LEFT 1-12->CENTER->RIGHT 1-12
SUBW VOL: (-6) - (+6)
Note:
The setting items below are not stored in
memory. After RESET or the back-up line
is disconnected, redo these settings. We
recommend you to take a note to keep the
records.

Radio Operations

Select tuner as playing source
Press [SRC / ] button once or more to
enter RADIO mode.
Selecting the radio band
Press the [BAND / ] button on the panel
to select one radio band among FM1, FM2,
FM3, MW and LW.
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press the [ ] or [ ] button on the
panel to tune in a higher / lower station.
Press the [ ] or [ ] button on the
remote control to select preset stations.
Auto tuning
Press and hold the [ ] or [
to seek a higher / lower station.
To stop searching, repeat the operation
above or press other buttons having radio
functions.
Note:
When a station is received, searching stops
and the station is played.
Preset scan
Preset scan receives the stations stored
in preset memory in order. This function is
]
useful when searching for a desired station
in memory.
1. Press the [PS/AS] button.
2. When a desired station is tuned in, press
the [PS/AS] button again to continue
receiving that station.
Note:
Be careful not to press and hold the [PS/AS]
button for 1 second or longer, otherwise the
auto store function will begin and the unit
starts storing stations.
Auto store
Only stations with sufficient signal strength will
be detected and stored in the memory.
Press and hold the [PS/AS] button (1 sec.) to
start automatic station search.
To stop auto store, press other buttons having
radio functions.
Notes:
1. After auto store, the previous stored
stations will be overwritten.
2. The unit has 5 bands, such as FM1, FM2,
FM3, MW and LW. FM3, MW and LW can
store by AS function. Each bands can store
6 stations, CZ702E can store 30 stations in
total.
Manual store
When one expected radio station has been
detected, press and hold number button 1-6 to
] button store it in the memory.
Recall the stored stations
Press one numeric button among 1 to 6 on
the panel to select the corresponding stored
station.
Local seeking
When LOCAL seeking is ON, only those
radio stations with strong radio signal could
be received.
To select LOCAL function, press and hold the
[ DISP ] button on the front panel, then press
[ ] button repeatedly until LO or DX
displays on the screen, and rotate the
[VOLUME] knob to select Local or Distant
mode.
Note:
The number of radio stations that can be
received will decrease after the local seeking
mode is ON.
9
CZ702E