Wall Mounting - Duracraft DW-210E Manual Del Usuario

FIRST TIME OF USE
1. Before starting to use the panel heater,
read through all the instructions.
2. Unpack the panel heater, all accessories
and the power cable. Remove all
packaging materials and dispose of them
in an environmentally friendly manner.
3. Stand the panel heater upside down.
Please note that the panel heater is only
standing upside down if the end of the
power cable leading into the appliance is
also on the top.
4. Fix the two castor undercarriages (12) on
the two ends of the base of the panel
heater. Adjust them so that each screw on
each undercarriage is fitted into its special
hole located on the base of the panel
heater. Tighten the castor undercarriages
(12) with a cross recess (Phillips-tip)
screw-driver. Make sure that the castor
undercarriages (12) are firmly attached to
the panel heater. (Fig.1)
5. Stand the panel heater upright on a firm,
even surface. Make sure the panel heater
is standing securely so that it cannot tip
over or fall off. Observe a safety distance
of at least 100 cm from other objects.
For use in bathrooms, a minimum distance
of 60 cm from showers, bathtubs and
washbasins must be observed, as shown
unter „safety distances" (1). The local
safety regulations of the country must al-
ways be observed.
6. When the panel heater is used for the first
time or after it has been stored for a
longer period, it could release a smell, but
this disappears after a short period of use.

WALL MOUNTING

(Fig. 2)
1. Make sure that the power switch (3) is in
the OFF position (4). Disconnect the
power plug (14) from the power socket.
Do not touch the power cable with wet
hands.
2. Hold the wall-mounting device (16) against
the wall and mark the first drilling hole. In-
sert a plug into the drilling hole. Observe
the minimum spacing as shown under safety
distances (1): at least 70cm to the floor
from the bottom edge of the panel heater
ENGLISH
and at least 100cm distance from the top
edge of the panel heater to other objects
(1). When mounting on a bathroom wall,
also make sure that the panel heater is at
least 60cm away from a shower, bathtub
or washbasin. The local safety regulations
of the country must always be observed.
3. After you have drilled the first hole, push
a plug into the hole and fix the holding
device (16) lightly to the wall on the one
side using a cross recess screw.
4. Mark the second drilling hole on the wall,
using a spirit level (distance of hole:
138 mm).
5. After you have drilled the second hole,
push the second plug into it and fix the
holding device (16) to the wall with the
second cross recess screw.
6. Tighten the cross recess screws. Make
sure that the holding device (16) is
attached firmly to the wall.
7. Using the device provided at the rear (15),
attach the panel heater without the castor
undercarriages to the wall-mounting device
(16) and press the panel heater lightly in
a downwards direction. Mark the other two
drilling holes for the wall-mounting devices
on the underside of the panel heater.
8. Remove the panel heater from the wall,
drill both holes and insert the remaining
plugs into the wall.
9. Again using the device provided at the
rear (15), attach the panel heater without
the castor undercarriages to the wall-mounting
device (16) and press the panel heater
lightly in a downwards direction. Make sure
that the panel heater is securely attached
to the wall-mounting device so that it cannot
fall off. Now attach the two wall-mounting
devices at the bottom of the panel heater
using the two remaining cross recess screws.
OPERATING INSTRUCTIONS
DW-210E panel heater 1000 Watt
DW-215E panel heater 1500 Watt
1. Make SURE that the power switch (3) is in
the OFF position (4). Connect the power
plug (14) with the power socket. Do not
touch the power cable with wet hands.
6