Product Description; Product Overview; Installation Instruction - Siemens SPCE120 Guia Del Usuario

English
Attention:
Before starting to install and work with this
device, please read the Safety Instructions.
This device shall only be connected to power
supplies compliant to EN60950-1, chapter 2.5
("limited power source").
Risk of damage to the device
Use the device only indoors and in dry
environments.
Do not expose it to dripping or splashing
water.
Do not let the contact areas of the board get
dusty and do not touch them with your bare
hands.

Product description

SPCE120 is a universal display module with 16
LEDs and 4 keys. In linked mode with the
SPCK620/23, the LEDs indicate the status of 4
areas which can be controlled with function buttons.
In flexible mode, the function of the LEDs and keys
can be freely programmed. The expander features a
buzzer for acoustic notification, an integrated
EM4102 card reader to activate LED's and function
keys and one freely programmable zone input.

Product overview

See Fig. 1: Product overview
1 Lugs for holding the PCB
2 Card reader
3 Buzzer
4 Rotary switches
5 Fixing screw for printed circuit board
6 X-BUS termination jumper (fitted by default)
7 Tamper switch
8 Jumper J3 (not used, open)
9 Breakout
10 Breakout
11 Holes for fastening
12 Lugs
Corrugated-head screw for back tamper
13
contact
14 Screw terminal
Assembly
Open housing
Loosen screws with several turns (Fig. 2).
Use a screwdriver to press the snap-fits down
and slightly lift the top of the housing
(Fig. 2, item 1).
Lift the housing top approx. 1 cm and push up
(Fig. 3).
Wire the device
Carefully bore open the breakout points
(Fig. 1 item 9) if necessary.
Connect the wires to the screw terminals (see
following table).
See Fig. 1, item 14: Contact pins
Contact Abbreviation Function
pin
1 IN1 Input
2 COM Input
3 1A X-BUS
4 1B X-BUS
5 2A X-BUS
6 2B X-BUS
7 0V Power supply negative
8 + 12 Power supply positive
9 SCL Not used
10 SDA Not used
Mount the bottom of the housing
Only mount the device on subsurfaces made of
stable materials.
Align the bottom of the housing.
Mark the locations for 3 holes for the fastening
screws (Fig. 1 item 11) and on hole for the
corrugated-head screw (Fig. 1 item 13).
Drill the holes and attach the bottom of the
housing with the screws.
Close the top of the housing
Hang the top of the housing on the top of the
bottom of the housing and press towards the
back.
The 2 snap-fits on the lower part of the bottom
of the housing snap in.
Tighten the two screws on the bottom side and
lead with the leading included in delivery (Fig. 5).
Wiring the X-BUS interface
The X-BUS interface provides connection of
expanders and keypads to the SPC controller. The
X-BUS can be wired in a number of different
configurations depending on the installation
requirements.
NOTE: Maximum System cable length = number of
Expanders and Keypads in the system x maximum
distance for cable type.
Cable type
CQR standard alarm cable
UTP category: 5 (solid core)
Belden 9829
IYSTY 2 x 2 x 0.6 (min)
Fig. 4 shows the wiring of the X-BUS to an
expander/controller and the following
expander/controller in Spur Configuration. Terminals
3A/3B and 4A/4B (if available for this module) are
only used for using a branch wiring technique. If
using a Spur configuration, the last expander is not
wired back to the controller.
See Fig. 4: Wiring of expanders
1 SPC controller
2 Previous expander
3 SPCE120
4 Next expander
Please refer to SPC Configuration Manual of
connected controller for further wiring instructions,
shielding, specifications and limitations.
X-BUS addressing
For addressing, reconfiguration, device location,
monitoring, editing of names, X-BUS type of
communication, failure timer please refer to SPC
Configuration Manual.
Overview of installation tools
See Fig. 6: Overview of installation tools
1 Connection element
2 Horizontal end piece
3 Vertical end piece
Middle piece (only for mounting 1
4
SPCK620/23 with 2 modules)
Installation with a keypad or other modules
Horizontal installation (e.g. 2 modules, Fig. 7)
Place 2 horizontal end pieces (Fig. 6 item 2) on
the end of a connection element (Fig. 6 item 1)
Snap the connection element into the connection
pins of the device so that the arrow on the
connection element is pointing up (Fig. 7).
Vertical installation (e.g. 1 module with
SPCK620/23, Fig. 8)
Place 2 vertical end pieces (Fig. 6 item 3) on the
ends of a connection element (Fig. 6 item 1)
Snap the connection element with the oval holes
towards the center onto the connection pins of the
device (Fig. 8)
Horizontal and vertical installation (e.g.
SPCK620/23 and 2 modules, Fig. 9)
Apply a vertical end piece to the 2 connection
elements on the end with the round holes
(Fig. 9 item 3).
Snap in the 2 vertical connection elements with the
Distance
oval holes towards the center on the
200 m
SPCK620/623.
400 m
Place 1 horizontal end piece (Fig. 6 item 1) on the
400 m
right end and a middle piece (Fig. 6 item 4) on the
400 m
left end of a connection element.
Snap the horizontal connection element onto the
connection pins of the device so that the arrow is
pointing up (Fig. 9).
Snap the vertical connection elements of the
SPCK onto the connection pins of the two
connected modules.
Technical data
LED indicators
Special keys
Number of on-board
zones
EOL resistor
Card reader
Operating voltage
Operating current
Quiescent current
1)
Field bus
Tamper contact
Operating
temperature
Relative humidity
Colour
Mounting
Housing
Dimensions
(W x H x D)
Weight
1)
Max. 400 m between devices / cable types IYSTY
2 x 2 x Ø 0.6 mm (min.), UTP cat5 (solid core) or Belden 9829

Installation Instruction

16 tri-color LED's, freely
programmable
4 function keys, freely
programmable
1, freely programmable
Dual 4K7 (default), other
resistor combinations
configurable
Integrated 125 kHz reader
(EM 4095)
9.5 – 14 V DC
Max. 90 mA at 12 V DC
(all LED's operated)
Min. 30 mA at 12 V DC
X-BUS on RS-485 (307 kb/s)
On-board front / back tamper
switch
-10 to +50 °C
Max. 90 % (non-condensing)
RAL 9003 (signal white)
Flat surface, wall-mounted
Plastic enclosure
(Polycarbonate)
112 x 92 x 28 mm
0.19 kg