Sevylor YUKON KCC380 Manual De Utilización página 4

FITTINGS
Floor chamber with
Mini Boston
Main chamber
valve
with recessed
Boston valve
Lifting
handle
Large
removable
storage
Removable fin
1/ Removable fin on the underside: see the assembly procedure.
This model comes with a back pack carry bag, a pressure gauge and a repair kit.
ASSEMBLY INSTRUCTIONS / INFLATION
Do not use a sharp tool!
For the first inflation and in order to get acquainted with your new product, inflate indoors at room temperature (about
E
20 °C) where the PVC will be soft and assembly process made easier.
N
If it was stored at a temperature below 0°C / 32°F, leave it at 20°C / 68°F for 12 hours before unfolding. Inflate it with an
G
inflator from Sevylor
L
other low pressure inflatables. These types of inflators will have a hose and adapters to fit the valves on this product.
I
S
H
Any use of an air compressor will damage your product and automatically void all warranties.
Choose a smooth and clean surface to unfold your product.
1. Attach the fin on the underside by folding the hull. Insert the extremities of the fin in the loops and stretch the hull as
much as possible to hold it in position. Once the kayak is inflated, this operation becomes impossible. The curvature of
the fin must be oriented towards the back end of the kayak.
2. Your canoe/kayak is equipped with following different types of valves:
a) Boston valve(s) – please see opposite figure: Unscrew the valve cap (1). Screw the
valve insert (2) onto its base (3) and check that the valve cap stays accessible.
Insert the pump hose end piece and inflate it until you will reach the required
pressure (see point 3). After inflation fit all the valve(s) cap tight (clockwise).
NOTICE: A slight air-leak before screwing the valve(s) cap is normal. Only the
valve(s) cap can ensure final AIR TIGHTNESS.
b) Double lock™ valve & Mini double lock™ valve – see drawing on page 2 / a:
Open the valve (A). To begin inflation, open external stopper and pull to extend out (B).
Insert nozzle of inflation device into the extended valve and turn on or begin pumping (C). To close valve: push in
with inflation device until stopper has been depressed, sealing internal stopper (D). Remove device and close
external stopper. Valve should appear depressed into itself (E).
c) Twist valve(s) – see drawing on page 2 / b:
Each spray deck chamber is equipped with a twist valve. It will give you more room for your legs and better
protection against water splash. To inflate open the twist valve by turning counter clockwise. After inflation turn the
valve clockwise to close the valve.
3. Inflate the kayak in the order of inflation as shown on the capacity plate printed on the product (see also figure # 1 –
numbering of the valves).
4. Max. air pressure: the correct pressure for this item is: 0,1 bar/1,5 PSI (= 100 mbar). Do not exceed it. Please
check the pressure with the supplied pressure gauge (refer to the "Instructions for the manometer"). Overpressure:
deflate until you reach the recommended pressure. Drop of pressure: inflate again slightly.
Ergonomic seats with elevated
sitting position with mini
double lock valve
™
2
3
1
Safety chamber
1
2 adjustable
with Mini Boston
footrests
™
valve
®
or any inflator designed for inflatable kayaks, rafts, pool floats, air beds, camping mattresses, and
Zipper to open nylon outer
hull & get access to PVC
™
air chambers
4
3
4
Neopren
Spray deck
chambers with
twist valve
CAUTION!
CAUTION!
4
Spray cover with
waterproof
pocket
Moulded
directional strake
Foam coaming
Lifting
handle
Bungee
cords
Figure 1
(1) Valve cap
( 2) Valve
insert
( 3) Valve
base