Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Remote Message Playback
•
Call your unit from a touch tone telephone.
•
After your PR970 answers, it plays the outgoing greeting and beeps once. Dial your three
digit security code within 20 seconds after the beep, pressing and holding each digit for 1
2 seconds. Allow a 2 second interval between each digit.
•
Your PR970 will sound one beep to indicate the code was entered correctly. If there are no
beeps, enter your code again.
•
Then you can press "1#" or "2#" on your keypad and the PR970 will playback the messages
recorded in Mailbox 1 or Mailbox 2, respectively.
Remote Record New Greeting
The PR970 enables you to change your outgoing greeting from a remote phone.
•
Call your unit from a touch tone telephone.
•
After your PR970 answers, it plays the outgoing greeting and beeps once. Dial your three
digit security code within 20 seconds after the beep, pressing and holding each digit for 1
2 seconds. Allow a 2 second interval between each digit.
•
Your PR970 will sound one beep to indicate the code was entered correctly. If there are no
beeps, enter your code again.
•
Press "8#".
•
When you hear a beep, begin recording your new greeting (up to 30 seconds).
•
When you have finished recording your new greeting, press "5#".
•
The unit will beep, and the new greeting will playback to you.
•
Hang up the telephone.
Remote Record Memo
•
Call your unit from a touch tone telephone.
•
After your PR970 answers, it plays the outgoing greeting and beeps once. Dial your three
digit security code within 20 seconds after the beep, pressing and holding each digit for 1
2 seconds. Allow a 2 second interval between each digit.
•
Your PR970 will sound one beep to indicate the code was entered correctly. If there are no
beeps, enter your code again.
•
Press "3#". Then within three seconds of pressing "3#" press "1#" or "2#" to select Mailbox
1 or Mailbox 2. Otherwise the memo will be recorded in Mailbox 1.
•
When you hear a beep, begin recording your memo (up to 60 seconds).
•
When you have finished recording your memo message, press "5#".
Remote Turn Off Answer On
If you forget to turn off the answer mode of your PR970, you can do this from a remote phone.
•
Call your unit from a touch tone telephone.
•
After your PR970 answers, it plays the outgoing greeting and beeps once. Dial your three
digit security code within 20 seconds after the beep, pressing and holding each digit for 1
2 seconds. Allow a 2 second interval between each digit.
•
Your PR970 will sound one beep to indicate the code was entered correctly. If there are no
beeps, enter your code again.
•
Press "9#".
•
You can now hang up.
PR970 – 9
Repeat Current Message
•
Press "4#" WHILE you are listening to the message. The message will be played again.
•
All following messages will then be played as usual and will be memorised when you hang
up.
Erase Current Message
•
Press "0#" WHILE you are listening to the message you wish to erase. The message will be
played to the end.
•
The following messages can be erased in the same way.
•
When you hang up, the message(s) will be automatically erased.
Repeat Previous Message
•
Press "4#" repeatedly WHILE you are listening to the message. The previous message will be
played again.
•
All following messages will then be played as usual and will be memorised when you hang
up.
Stop Message Playback
•
Press "5#" WHILE you are listening to the message.
•
All messages will be memorised when you hang up.
Skip to Next Message
•
Press "6#" WHILE you are listening to the message. The next message will be played.
•
All following messages will then be played as usual and will be memorised when you hang
up.
IMPORTANT!
If your appliance is not operating properly before contacting a Service Center we advise you to
do a "RESET" of your unit. In many cases, the appliance will again function normally after you
have done this.
To reset unit:
•
Unplug the telephone line from the wall jack.
•
Unplug the AC adapter from the power outlet.
•
Remove the AAA batteries, and then replace.
•
Plug the AC adapter back into the power outlet.
•
Plug the telephone line back into the wall jack.
•
Record a new outgoing greeting or you can use the pre recorded announcement.
•
Reset the Voice Day/Time Stamp.
ATTENTION!
This RESET erases all information (e.g. programmed day and time indication, outgoing greeting,
etc. will be erased)!
PR970 – 10
Publicidad
Tabla de contenido
