Dust extraction (fig. O)
The machine is provided with two dust extraction connection points.
One is situated at the rear of the machine casing (56), and the other is in
the upper blade guard (57).
• To provide the best dust extraction results, it is recommended that
both points are connected to a suitable dust extraction device during
all sawing operations.
• Whenever possible, connect a dust extraction device designed in
accordance with the relevant regulations regarding dust emission.
Optional attachments (fig. P1)
The attachments, i.e. the legstand (15), extension table (16), parallel fence
(17) and sliding table with long mitre fence end stop (18) are available as
an option.
Consult your dealer for further information on the appropriate accessories.
Legstand (fig. A2 & P2)
The legstand has been designed for intstalling your saw bench as a stand-
alone machine acquiring optimum space for using the extension table (16)
and/or the sliding table (18) (fig. A2).
• Place the legstand (16) on the floor leaving enough space to use freely
any attachment mounted to the machine (fig. P2).
• Place the machine on the legstand making sure that the four feet on
the machine are located within the frame.
Extension table (fig. A3 & P3)
The extension table (16) utilises the same dovetail system for location and
can therefore be fitted onto any side of the table (fig. A3).
• The most suitable position is on the right-hand side of the machine (fig. P3).
• The fence assembly can be used on the extension table in the same
way as on the machine table.
Parallel fence (fig. A4 & P4)
The parallel fence (17) is used in the ripping mode to extend the ripping
guidance over the full length of the table (fig. A4).
• The parallel fence is to be mounted to the right of the blade.
• Utilizing the same dovetail system for location, the parallel fence can be
mounted either on the machine table or on the extension table.
• Preferably mount the parallel fence (17) on the extension table (16)
(fig. P4).
• Refer to the instructions for sawing in ripping mode.
Sliding table with long mitre fence end stop (fig. A5 & P5 - P7)
The sliding table with long mitre fence end stop (18) is used in the ripping
mode to support cross-cutting long workpieces at any angle from 0° to
90° (fig. A5).
• The only suitable position for the sliding table (58) is on the left-hand
side of the machine (fig. P5).
• Utilizing the same dovetail system for location, the mitre fence (59) is to
be mounted to the left-hand side of the sliding table.
• Set the blade in ripping position.
• For straight cross-cuts, set the fence at 90° to the blade (fig. P6).
• For mitre cuts, set the required angle (fig P7).
• Place the workpiece against the mitre fence.
• Before making a cut, check that the fence does not foul the blade and
that the workpiece will be cut through.
• Slowly push the table to the rear, thus feeding the workpiece along
the blade.
22
Maintenance
Your Elu machine has been designed to operate over a long period of time
with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Cleaning
Keep the ventilation slots clear and regularly clean the housing with a
soft cloth.
• On a weekly basis, remove sawdust from the machine.
Unwanted tools and the environment
Take your tool to an Elu authorized repair agent where it will be disposed
of in an environmentally safe way.
Elu After-Sales service
All Elu products are thoroughly tested before leaving the factory. However,
if the product needs repair, please contact your dealer or the Elu Head
Office for the address of the nearest Elu authorized repair agent (please
refer to the back of this manual). Alternatively, a list of authorized Elu repair
agents and full details on our after-sales service are available on the
Internet at www.2helpU.com.
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of your Elu
tool, simply return it within 30 days, complete as purchased, to your
Elu dealer for a full refund or exchange. Proof of purchase must be
provided.
• ONE YEAR FULL WARRANTY •
If your Elu product becomes defective due to faulty materials or
workmanship within 12 months from the date of purchase,
we guarantee to replace all defective parts free of charge or, at our
discretion, replace the unit free of charge provided that:
• The product has not been misused.
• Repairs have not been attempted by unauthorized persons.
• Proof of purchase date is provided.
This guarantee is offered as an extra benefit and is additional to
consumers statutory rights.
E N G L I S H
GUARANTEE
en - 7