Publicidad
Idiomas disponibles
Idiomas disponibles
Access hole
Attachment
Leave 1" Tab
hole
Rear
Figure 1
1.
Remove Underbody Panel – (If installed) Remove (10) screws (with 5.5mm socket) and (2) plastic nuts (with 10mm socket).
2.
Lower Exhaust– Using exhaust removal pliers and some lubrication remove the rubber isolator from the hanger. Note: The 1.0L turbo will have 1 hanger on the passenger side and
the 2.0L will have a hanger on each side. Note: The passenger side isolator is best to be removed from the top hanger and on the driver side the isolator is best to be removed from
the bottom hanger.
3.
Remove Fasteners– Remove the (2) vertical 10mm bolts(with 15mm socket), each side (4 bolts total). Note: If extra clearance is needed disconnect the electrical wire from the driver
side frame rail. (Remove by pulling down on the attachment housing)
4.
Raise Hitch- Raise the hitch over the passenger side hanger first, then raise the hitch over the driver side hanger, and slide into place.
5.
Install Fasteners– Install the supplied fasteners as shown in figure 1. Items
hole, to the attachment hole and install items
6.
Torque Fasteners– Torque all 1/2"-13 GR5 fasteners to 50 Lb-Ft (68 n-m) and all 10mm-1.5 CL10.9 fasteners to 38 Lb-Ft (52 n-m)
7.
Raise Exhaust- Raise exhaust and reattach hangers. Note: Reconnect the electrical wire if removed in step 3.
8.
Trim Underbody Panel- (If installed) Trim the underbody panel (SEE FIGURE 2). Using the holes for the 10mm fasteners (not centered) measure 4 5/16" from the passenger side
attachment hole and mark the center line. Trim a 5 1/2"x 6" section in the center/rear of the panel. Then Trim a 2" section 20 5/16" from the center line to the passenger side
leaving a 1" tab in the rear to reattach to the fascia. Then trim a 2" section 17 1/4" from the center line to the driver side leaving a 1" tab in the rear to reattach the fascia. Then
install.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been
damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and
requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2018 Horizon Global™ Corp. - Printed in Mexico
Installation Instructions
PART NUMBERS: 36660, 06190, CQT36660
5 1/2"
6"
17 1/4"
4 5/16"
Figure 2
2"
C L
Frame Rail
Weld Nuts
o
m
n
k
k
l
j
j
j
k
and
l m
n
and
.
Leave 1" Tab
5 1/2"
20 5/16"
2"
20 5/16"
Authorized Drawbar Kit:
36071 (Sold Separately)
Drawbar must be used in the
RISE position only.
will be installed onto the existing weld nuts. Item
Sheet 3 of 15
Fastener Kit: 36660F
j
Qty. (4)
Hex Bolt
M10x1.5x35mm
CL10.9
k
Qty. (4)
Conical Washer
3/8"
Part# 01292006
l
Qty. (2)
Hex Bolt
1/2"-13 x 1.5"
GR5
m
Qty. (2)
Flat Washer
1/2"
n
Qty. (2)
Lock Washer
1/2"
o
Qty. (2)
Handle Nut
1/2"-13
Part#1332
Fasteners
typical
Conical Washer
both sides
Against hitch
Always wear SAFETY GLASSES
when installing hitch
o
will be formed a inserted into the access
Proper torque is needed to keep the
hitch secure to the vehicle when towing.
36660NP
02-09-18
Teeth side
Rev. A
Publicidad
