Cleaning And Maintenance - Stokke TRIPP TRAPP Guia De Inicio Rapido

User Guide ........................................................................
4 US
READ CAREFULLY BEFORE ASSEMBLING
YOUR TRIPP TRAPP® HIGH CHAIR.
On the fold out page of this user guide you will nd pictures that
describe the assembly of your Tripp Trapp® high chair and Tripp
Trapp® Baby Rail. The Baby rail should only be used with the seat
plate in the rst groove from top of high chair.
Parts
10 Metal screws • 6 Metal nuts • 1 Allen Key • 2 Curved backrests
2 Metal cross bars • 1 Wooden base cross bar • 1 Seat • 1 Footrest • 2 Legs
1. Attach the base cross bar to the legs (grooves face inside).
Important to insert the shallow end of nut rst!
2. Insert screws and tighten rmly.
3. Attach the two metal crossbars and tighten loosely
4. Attach the two curved back rests. Insert metal nut with shallow
end rst and tighten loosely. NOTE: Backrest with strap goes
into bottom slots.
5. Slide seat and footrest into slots, with straight edge facing for
ward. Make sure the height and depth of the seat and footrest
suit the size of your child (see instructions for seat and footrest
adjustments in this user guide).
6. Place the high chair on a level surface. Finally tighten all screws
rmly in the order given.
SEAT AND FOOTREST ADJUSTMENT
It is important to adjust the depth and height of the seat and foot-
rest to fit the size of your child. See illustrations on the fold out
page, and description below. The settings of the seat and footrest
should be checked as the child grows – at least once a year!
The seat plate and the footrest must be supported by the full
length of the grooves on the sides (not half way supported).
Seat placement
Height - The seat is set at the correct height when your child's
elbows are level with the table top.
Depth - For correct depth of the seat, position the child's back
against the backrest with the seat supporting ¾ of the thighs. For
the child's best comfort it is important that the seat depth is not
too deep. Leave comfortable space between the front edge of the
seat and back of the child's knee.
For a child 6-8 months it may amaze you how small seat they
actually need! The seat plate should not protrude more than ¾-2"
(2-5cm) in front of the chair side legs.
AGE SEAT
6 months 1
1 1/2 year 2
3 year 2
7 year 3
10 year 4
Teen/ Adult n.a.
*) Use footrest as seat. Therefore seat is not
applicable.
070905_TT_User_Guide.indd 4-5
TABLE OF AGE AND
FOOTREST
APPROXIMATE
ADJUSTMENT
5
This table is a rough guide
6 for the height adjustment
of seat and footrest ac-
8
cording to the age of you
child. Child di er in size
11
according to age, so al-
ways make sure that your
14
child is seated correctly ac-
4-5*
cording to the instructions
given in this user guide.
................................................................ User Guide
Footrest placement
Height – The footrest is set at the correct
height when the sole of the child's foot can
rest at on the footrest, while the thighs are
touching the seat.
Depth – Make sure the forward edge of the
footrest NEVER exceeds the front tip of the
chair legs at oor level
RESTRAINT SYSTEM OPERATION
Always use the restraint system when the
seat is in the 1st, 2nd or 3rd grooves from
the top. Place child in seat. Pull each arm
through the loop formed by the shoulder
and waist strap, and place in child's lap.
Crotch strap comes up between child's legs.
Attach each shoulder strap to the crotch
strap. Adjust length of shoulder, waist and
crotch strap to restrain child in seat. Crotch
strap length should be adjusted so that con-
nector is at waist height.
The restraint system can be removed when
your child has reached the age of 36 months
AND is able to sit safely on TRIPP TRAPP®.
Use a tool to remove the spring under the
seat plate to detach the crotch strap. Use a
screwdriver to detach the rest of the harness
from the backrest.
WARRANTY
7 years warranty on all wooden and metal parts; 2 years warranty on
textile parts. All related to material or workmanship defects.
This warranty does NOT apply to defects from normal wear and
tear, product misuse, after market product alterations, used with
non-STOKKE approved and marked accessories, or failure to follow
TM
assembly, use and care instructions supplied with the product.
If any defect is discovered, please return the product for inspection,
with the receipt or other proof of purchase, to the retailer where
it was purchased. Underneath one of the legs of your Tripp Trapp®
high chair there is a barcode with a unique serial number. This
number is ALWAYS required if you have a claim.
Product information: The chair is made of cultivated beech wood.
The varnish contains no harmful substances, and the liberation of
formaldehyde from the varnish complies with E1 require-
ments.
Safety approval: Tripp Trapp® high chair complies with
ASTM F404-07. Tripp Trapp® high chair is JPMA certified.

CLEANING AND MAINTENANCE

Wipe with a clean damp cloth, wipe o excess of water with a dry
cloth. Moisture will crack stain. We do not recommend the use of
any detergent or micro bre cloth.
Colours may change if the high chair is exposed to the sun.
US 5
ACCESSORIES
Tripp Trapp® Cushion
Comes in several colours
and designs. It ts your Tripp
Trapp® high chair both with
and without Tripp Trapp®
Baby Rail.
Tripp Trapp® Baby Rail
Baby rail intended for chil-
dren from 6 months and up
to 2 years.
ASTM F404 - 07
05-09-07 15:48:56