Tabla de contenido
Publicidad
SAFETY INSTRUCTIONS
© Stanley Bostitch
IMPORTANT READ CAREFULLY: It is important that all operators read and understand all sections of this
Tool Technical Data manual and the separate Safety and Operating Instruction
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
Manual which come with this tool. Failure to do so could result in you or others in the working area to be seriously
compliance for the products.
injured.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
WARNING! Eye protection in accordance with 89/686/EEC, and with equal or greater grade than defined in EN166
rien que les produits soient conformes aux normes CE.
should be used. However all aspects of operators work, environment and other type/s of machinery being used, should
also be considered when selecting any personal protection equipment. Note: Non-side shielded spectacles and face
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
shields alone do not provide adequate protection.
die CE-Richtlinien für Produkte.
WARNING! To prevent accidental injuries:
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
•
Never place a hand or any other part of the body in fastener discharge area of tool.
zeggen dat de producten voldoen aan de CE-vereisten.
•
Never point tool at yourself or anyone whether it contains fasteners or not.
•
Never engage in horseplay.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
•
Never pull the trigger unless the nose is directed towards the work.
produkterne.
•
Always handle the tool with care.
•
This tool is intended to be used for sealing cardboard cartons and similar material. DO NOT USE for fastening harder
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
materials which could cause buckling of the staples and damage to the tool.
yhdenmukaisuutta.
•
To prevent accidental actuation and possible injury, always disconnect air supply.
1. Before making adjustments. 2. When servicing the tool. 3. When clearing a jam. 4. When tool is not in use. 5. When
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
moving to a different work area, as accidental actuation may occur, possibly causing injury.
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
•
Read the additional Safety & Operating instructions booklet before using tool.
•
Do not use oxygen and combustible gases as an energy source for pneumatically operated tools.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
•
The operation of this tool can cause sparks and act as a source of ignition for flammable fuels and gases.
conformità CE per i relativi prodotti.
•
Shuttle will stay in the down position until the trigger is released. Please read the relevant section in the
Safety & Operating Instructions manual for more details.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
merking for produktet.
LOADING THE TOOL
1. Disengage the latch and pull back magazine side. (Fig. 1)
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
2. With magazine fully open, insert fasteners. Points must be against bottom of magazine. (Fig. 2)
conformidade com a CE para os produtos.
3. Push magazine forward. (Fig. 3)
4. Continue pushing until latch is engaged.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
Note: Use only fasteners recommended by Bostitch for use in Bostitch tools or fasteners that meet Bostitch
specifications.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
LOADING THE TOOL FOR 10mm STAPLES (P51-5B / P51-10B)
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
These tools require a different shuttle to be fitted for use with 10mm length staples. Repairs shall only be
stanowią deklaracji zgodności CE prezentowanych produktów.
carried out by the authorised agents of Bostitch or by other experts, giving due regard to the safety, operating
and maintenance instructions in this manual and tool technical data.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
1. Remove cap and piston head bumper.
stanowią deklaracji zgodności CE prezentowanych produktów.
2. Disconnect magazine and pull to rear.
3. Pull out cylinder assembly.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
4. Remove driver and guide screws.
výrobky.
TROUBLE SHOOTING
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
a termék CE-megfelelőségét.
Problem: Shuttle Punches Through Board:
Solution: Pressure too high; staple leg too short.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
Problem: Staple Leg Buckles And Flattens Against Work Surface:
Solution: Staple leg too long, shuttle not down against work due to worn shuttle piston o-ring.
GB
Publicidad
Tabla de contenido
