Fontanot RING TUBE Instrucciones Para El Ensamblaje página 7

25. Position the "X" initial baluster (C67). Adjust the height of a long baluster (C67) cutting the end to the same
height as those already assembled (fig. 1).
26. Secure element F34 in a position corresponding to the first baluster (C67) drilling a hole with a Ø 8 mm point.
Use elements C58, B12, B83 and B02 (fig. 1).
27. Prepare spiral handrails A71 (p. 46).
28. Determine the length of the bars A28 based on the staircase dimensions and cut them (fig. 1a). Insert the
bars A28 in the parts D39 previously assembled on the "Y" C67 intermediate balusters and in the parts D75
previously assembled on the "X" C67 end balusters (fig. 1a) (fig. 3-3a). Join the bars A28 to each other using
the part A41 and the glue provided (fig. 1a). Finally, tighten the parts C76 on the part D75.
29. Assemble the BG5, D40 and C76 elements on the "Y" C67 intermediate baluster, located halfway up the
staircase (fig. 1a).
Assembling the balustrade
33. Assemble the column (C73) on element G01 protruding from the landing (E02), positioning articles D75 towards
the outside, using elements D49 (fig. 8) (fig. 1).
34. Position elements F34, using elements C58, B83, B02 on the landing (E02). Drill the landing (E02) using a
Ø 5 mm point, maintaining the same centre to centre distance between the holes as the one used between the
balusters (C67) of the railings assembled before.
35. Position the "X" end balusters and the "Y" intermediate (C68) balusters with the D75 and D39 elements placed
outwards and tighten the elements B02 of the articles F34 (fig. 1) (fig. 3a).
36. Cut 5cm off the straight handrail BH4. Drill a hole in the top using a 3.5mm Ø point and assemble the parts
BG4, BG3 with the screw BB3 (fig. 9a).
37. Fit the assembly obtained with the elements BD2, BG2, BH1 and BG8 on the element C73 and tighten with the
dowel BC3 (fig. 1). Assemble the straight handrail BH4 on the element C73 and tighten with the element BB6
(fig. 9a).
38. Cut the other end of the straight handrail BH4 based on the dimensions of the balustrade, drill a hole using a
6 mm Ø bit to fasten the part BG4 or drill a hole using a 3,5 mm Ø bit to fasten the parts BG2+BG3 with the
parts BB3. Fasten the handrail BH4 using the parts CD3, checking that the balusters are vertical. Tighten the
parts B02 (fig. 1).
39. Determine the length of the bars A28 based on the dimension of the balustrade and cut them (fig. 1).
40. Based on the position and the existence of walls around the opening of the staircase, one or two (C03) extra
balusters may need to be positioned (fig. 10).
41. In this case, consider a space equidistant from the other balusters or from the wall. To secure these, we
recommend drilling the landing (E02) with a Ø 5 mm point and using elements F34, C58, B83, B02. We also
recommend drilling the floor with a Ø 14 mm point and using elements F34, B02, B13 (fig. 10).
Final Assembly
42. To further stiffen the staircase at intermediate points, secure elements F09 to the wall and join using elements
F33, with the balusters (C67). Drill using a Ø 8 mm point and use elements C50, C49, C58, B12 (fig. 11).
7 - RING TUBE L