Extremis Hopper Picnic Manual página 30

English
ASSEMBLY
Hopper picnic
1. Remove the lid of the box. The packaging materi-
al must stay intact for the rest of the assembly!
2. Remove the four screws from the two boards that
prevent the table legs from moving during
transport. Fold down the cardboard flaps to have
better access to the legs. Take them out the box
and position them as shown in the drawing (de
pending on the size of the table).
3. Put the lid back on the box.
4. Put the 2 boards mentioned in step 2 on top of
the lid.
5. Put the tabletop with its frame facing downwards
on top of the two boards. The top of the legs are
now at the same height as the tabletop.
6. Position the legs to the tabletop.
7 Put 3 bolts M10x30 in the square holes of each
table leg. Screw the supplied nuts and spring
washers onto the threaded rods, but do not tigh-
ten them yet.
7 . Screw the supplied nuts and spring washers onto
the threaded rods, but do not tighten them yet.
8. Before assembling the benches, remove the
packaging material from under the frame!
9. Fasten the bench to the legs in the same way
described above. Now tighten all the nuts.
Hopper combi
1. Remove the lid of the box. The packaging materi-
al must stay intact for the rest of the assembly!
2. Remove the four screws from the two boards that
prevent the table legs from moving during
transport. Fold down the cardboard flaps to have
better access to the legs. Take them out the box
and position them as shown in the drawing (de
pending on the size of the table).
3. Put the lid back on the box.
4. Put the 2 boards mentioned in step 2 on top of
the lid.
5. Put the tabletop with its frame facing downwards
on top of the two boards. The top of the legs are
now at the same height as the tabletop.
6. Position the legs to the tabletop.
7 . Put 3 bolts M10x30 in the square holes of each
table leg. Screw the supplied nuts and spring
washers onto the threaded rods, but do not tigh-
ten them yet.
7 . Screw the supplied nuts and spring washers onto
the threaded rods, but do not tighten them yet.
8. Before assembling the benches, remove the
packaging material from under the frame!
30
All manuals and user guides at all-guides.com
9. Fasten the bench to the legs in the same way
1 . Unscrew the 2 nuts and spring washers at the
1 . Unscrew the 2 nuts and spring washers at the
2 . Position the back supports on the bottom of the
2 . Position the back supports on the bottom of the
3. Screw the wooden shelf to the supports, each
1. Lay the tabletop on trestles.
2. Position the legs to the tabletop.
3 . Put 3 bolts M10x30 through the square holes
3 . Screw the wooden shelf to the supports, each
MAINTENANCE
Wood
Iroko wood and Hellwood requires little or no main-
tenance. However, we strongly advise you to remove
persistent dirt. To clean the wood you can use speci-
al products (www.rmc-extremis.be) or simply a stiff
bristle brush and some water. Be careful not to irre-
parably damage the wood fibres. For this reason,
never use a high pressure cleaner as this will
roughen the wood's smooth surface and irreparably
damage the wood's fibres.
At first, the wood will give off this red dye every time
it comes into contact with water. The dye that drips
onto the frame and the surface will remain water-so-
luble and will dissapear entirely after a while.
We strongly recommend that you treat your wood for
indoor use with wood oil to protect it from stains.
When delivered, the wooden parts of our products
are untreated. Exposure to sun and rain will gradual-
described above. Now tighten all the nuts.
Backrest
outside of the bench frame. Now also remove the
2 bolts M10x30. The bolt and nut on the insed
will prevent the bench from falling.
outside of the bench frame. The nut on the insed
will prevent the bench from falling.
bench and fasten it by inserting put 2 bolts
M10x40 in the square holes on either side and
screw 2 nuts & spring washer onto the threaded
rods.
bench and fasten it by 2 nuts onto the threaded
rods.
time using 3 screws 5x25. Use the pre-drilled
holes to correctly position the backrest.
Hopper table
of each table leg. Screw the supplied nuts and
spring washers onto the threaded rods.
time using 3 screws 5x25. Use the pre-drilled
holes to correctly position the backrest.