Publicidad
Idiomas disponibles
Idiomas disponibles
INSTRUCTIONS MANUAL
Digital multimeter
KPS-MT70
Cod: 602250033
SKU: KPSMT70CBINT
Digital multimeter
ENGLISH
INTRODUCTION
The digital multimeter is designed and manufactured according to safety requirements of
EN 61010-1, EN 61010-2-030, EN 61010-2-033, EN 61010-031 on electronic measuring
instrument and hand held digital multipurpose meter. And conforms to UL STD.61010-1,
61010-2-030, 61010-2-033, Certified to CSA STD.C22.2 NO.61010-1, 61010-2-030, IEC
STD61010-2-033.
The product meets with the requirements of 600V CAT III and pollution degree 2.
The meter can be used for measuring DC voltage, AC voltage, resistance, diode, capacitance,
Continuity test, DC current and AC current etc. The unique non-contact AC voltage detection
function can promptly remind you to pay attention to safety operation, the full scale AC 250V
protection design makes you more safe and relieved.
This series of meters can be widely used for schools, labs, research institutes, enterprises and
factories etc. various electronic industries Please read this operating instruction carefully and
pay attention to related safe working standards before using this meter , Protection provided
by the instrument will be impaired if used in a manner not specified by the manufacturer.
SAFETY INFORMATION
WARNING
The special attention should be paid when using the meter because the
improper usage may cause electric shock and damage the meter .The safety
measures in common safety regulations and operating instruction should
be complied with when using. In order to make fully use of its functions
and ensure safe operations please comply with the usage in this section
carefully.
In order to avoid personal injury and meter damage caused by electric shock, the following
safety tips should be paid attention to:
• Don't measure any voltage out of stipulated measuring range of the meter.
• Don't apply high voltage (above 100V) at input end when measuring resistance and diode.
• Don't use the meter if the test line is damaged or exposed metal part.
• Avoid using under direct sunlight or high temperature.
• Pay attention to the possibility of electric shock when measuring voltage in excess of 36V
AC or 48V DC.
• Before measuring current, firstly turn off the power of measured equipment and measured
circuit, Electrify to measure after connecting test leads.
• Pay attention to battery polarity when changing battery.
• Measure known voltage with the meter to verify that the meter is working properly. If
the meter is working abnormally, stop using it immediately. A protective device may be
damaged. If there is any doubt, please have the meter inspected by a qualified technician.
MAINTENANCE
• Before removing the rear cover, disconnect the probe from the circuit to be measured.
• To protect the internal circuit, replace the fuse with one of the same specification: FF
600mA H 600V
• Don't use the instrument until the rear cover is placed back and the screws are tightened.
• Clean the housing of instrument only with a wet rag dripped with little detergent but never
chemical solution.
• In case of any abnormality, stop using it and sent it for maintenance..
WARNING
To avoid electrical shock, remove test leads before replacing battery or fuse
and cleaning.
AUTOMATIC POWER-OFF
1) If there is no operation during any 15 minutes after turning the machine on, the meter will
enter sleeping state. Within 1 minute before shutdown, buzzer will sound.
2) After automatic power-off, press
key, the meter will turn on again.
REPLACING THE BATTERIES
WARNING
To avoid electric shock, make sure that the test leads have been clearly
move away from the circuit under measurement before opening the battery
cover of the meter.
WARNING
Do not mix old and new batteries. Do not mix alkaline, standard (carbon-
zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
1) If the sign "
" appears, it means that the batteries should be replaced.
2) Loosen the fixing screw of the battery cover and remove it.
3) Replace the exhausted batteries with new ones.
4) Put the battery cover back and fix it again to its origin form.
Note: Do not reverse the polarity of the batteries.
EN
FUSE REPLACEMENT
The steps for replacing the fuse are:
1. Switch off the power.
2. Open lower cover with screwdriver to take out the broken fuse.
3. Load the fuse with same Electrical specifications (FF 600mA H 600V), recover battery
cover and make the screw fixed.
CLEANING
When the meter surface is required to clean, please use soft cloth, don't use organic solvent
with corrosive and solvent action to the case.
instruction manual:
APAC: MGL GLOBAL SOLUTIONS LTD
info.apac@mgl-intl.com
Flat 4-1, 4/F, No. 35, Section 3 Minquan
East Road. Taipei, Taiwan.
Tel: +886 2-2508-0877
EMEA: MGL EUMAN S.L.
info.emea@mgl-intl.com
Parque Empresarial Argame, 33163
Morcín. Asturias, Spain.
Tel: +34 985-08-18-70
Digital multimeter
See the full
AMERICAS: MGL AMERICA, LLC.
info.na@mgl-intl.com
US East Coast: 2810 Coliseum Centre
Drive, Ste. 100. Charlotte, North Carolina,
28217 USA
Tel: +1 833 533-5899
US West Coast: 760 Challenger Street.
MGL EUMAN S.L.
Brea, California 92821 USA
Parque Empresarial de Argame,
Tel: +1 310-728-6220
C/Picu Castiellu, Parcelas i-1 a i-3
E-33163 Argame, Morcín
www.mgl-intl.com
Asturias, España, (Spain)
Publicidad
