Product Description And Specifications; Product Features; Items Included - Bosch GTA 6000 Professional Manual Original

Firmly secure the power tool to the saw stand before
u
using it. You may lose control of the power tool if it slips
on the saw stand.
Place the saw stand on a firm, flat, horizontal surface.
u
If there is a chance that the saw stand will slip or wobble,
the safe and steady machining of the workpiece cannot
be guaranteed.
Do not overload the saw stand or climb or stand on it.
u
Overloading or standing on the saw stand can raise its
centre of gravity, causing it to tip over.
Do not force the workpiece into the saw blade. Exert-
u
ing excessive pressure on the power tool can cause the
saw stand to tip over.
Ensure that all screws and connecting pieces are
u
tightly fastened when carrying out work. Loose con-
nections can cause instability and inaccurate sawing.
Ensure that long and heavy workpieces do not unbal-
u
ance the saw stand. The free end of long and heavy
workpieces must have something placed underneath it or
be supported.
When pushing together or pulling apart the saw stand,
u
do not put your fingers near the points of articulation.
There is a risk of fingers being crushed.
Symbols
The following symbols may provide you with important in-
formation about the use of your saw stand. Please take note
of these symbols and their meaning. Knowing what these
symbols mean will help you to use your saw stand more ef-
fectively and more safely.
Symbols and their meaning
The maximum load bearing capacity
(power tool + workpiece) of the saw
stand is 100 kg.
Product description and
specifications
Intended Use
The saw stand is intended for holding the following Bosch
benchtop saws (stand 2021.08):
– GTS 10 XC (3 601 L30 4..)
The saw stand and power tool are intended for cutting
boards and profiles.

Product Features

The numbering of the components shown refers to the illus-
trations on the graphics pages at the beginning of the
manual.
(1) Release lever
(2) Base frame
Bosch Power Tools
(3) Saw stand leg
(4) Fastening set
(5) Power tool fastening set
Technical Data
Saw stand
Article number
Base frame dimensions
Saw stand height
Max. load bearing capacity
(power tool + workpiece)
Weight according to EPTA-Pro-
cedure 01:2014
Assembly

Items included

See the list of items included at the start of the
operating manual.
Check to ensure that all the parts listed below have been
supplied before assembling the saw stand:
– Base frame (2)
– Saw stand legs (3) (4 pieces)
– Fastening set (4) consisting of:
Cross-head screws M8 x 45 (4 pieces),
lock nuts M8 (4 pieces)
– Fastening set (5) consisting of:
Hex screws M8 x 75 (4 pieces)
washers M8/18 mm (8 pieces),
nuts M8 (4 pieces)
Extra tools required (not included in the delivery):
– Cross-headed screwdriver
– Open-end spanner (13 mm)
Assembling the saw stand (see figures A1−A2)
Carefully remove all parts included in the delivery from their
packaging.
Remove all packing material.
– Place the folded base frame (2) flat on the floor.
– Pull up the base frame (2) by the unlocking lever (1).
Let go of the unlocking lever whilst pulling it up so the saw
stand can click into place.
– Insert the saw stand legs (3) into the square pipes in the
base frame (2) until they are aligned with the assembly
holes.
– Screw together the saw stand legs and the base frame us-
ing the nuts and bolts in the fastening set (4).
Securing the power tool (see figure B)
– Centre the power tool on the base frame (2).
English | 7
GTA 6000
3 601 M24 10.
mm 670 x 750
mm 602
kg 100
kg 12.5
1 609 92A 72L | (15.09.2021)