Bostitch BF33 Instrucciones De Funcionamiento Y Seguridad página 14

All manuals and user guides at all-guides.com
Inserting and Removing the
Battery Pack from the Tool (fi g. 2)
WARNING: To reduce the risk of
serious personal injury, lock tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up can
cause injury.
NOTE: Make sure your battery pack (l) is fully
charged. The battery packs supplied will not
necessarily be fully charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL
HANDLE
1. Align the notch inside the tool's handle with
the battery pack (l).
2. Slide the battery pack firmly into the handle
until you hear the lock snap into place.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the release button (n) and slide the
battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this
manual.
FUEL GAUGE BATTERY PACKS (FIG. 2, 2A)
Some Bostitch battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the
fuel gauge button (o). A combination of the three
green LED lights will illuminate designating the
level of charge left. When the level of charge in the
battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be
recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-
user application.
NOTICE: Do not store tool with battery
pack installed. To prevent damage to
the pack and to ensure best battery
life, store battery packs out of the tool
or charger in a cool, dry location.
Rotating Rafter/Belt Hook (fi g. 6)
The rafter/belt hook (j) and can be easily positioned
to the left or right of the tool to accommodate left-
or right-handed users.
If use of the hook is not desired at all, it can be
rotated to the front or back of the handle base.
12
Loading the Tool (fi g. 4)
WARNING: Always lock tool off and
disconnect battery pack before loading
and unloading fasteners.
1. Slide the spring-loaded pusher latch (h) to the
base of the magazine to lock it into place.
2. Select an appropriate collated nail stick. (Refer
to Technical Data.) Bostitch would always
recommend that you use Bostitch branded
first fix nails.
WARNING: Since accessories, other
than those offered by Bostitch, have
not been tested with this product,
use of such accessories with this tool
could be hazardous. To reduce the risk
of injury, only Bostitch recommended
accessories should be used with this
product.
3. Insert collated nail stick into the loading slot on
side of the magazine. Be sure the fasteners
ride on their tips in the nail channel.
4. Close the magazine by releasing the pusher
latch. Carefully allow the latch to slide forward
and engage the nail strip.
Dry Fire Lock out
The nailer is equipped with a dry fire lock out
which restricts the tool from actuating when the
magazine is nearly empty. When approximately 7
to 9 nails remain in the magazine, the tool dry fire
lock actuates. Refer to Loading the Tool to reload
a stick of collated nails.
NOTE: If heavy force is placed on the tool it is
possible to override the lock out. This protects the
tool from potential damage if dropped.
Adjusting the Driving Depth (fi g. 5)
The nail driving depth can be adjusted using the
depth adjustment wheel.
1. To drive the nail shallower, rotate the depth
adjustment wheel (d) to the left, toward the
shallow nail icon.
2. To sink a nail deeper, rotate the depth
adjustment wheel (d) to the right, toward the
deeper nail icon.
Selecting the Mode (fi g. 1)
BF33 ONLY
To select sequential action mode, slide the mode
selector switch (i) to display the single nail
icon ( ).
To select bump action mode, slide the mode
selector switch (i) to display the three nail
icon ( ).