DeWalt DW746 Manual De Instrucciones página 34

E N G L I S H
• Remove the motor cover and parts box from the interior of the saw.
• Cut the strap holding the motor.
• Put the saw into the upright position.
• Lower the motor using the height adjuster and remove the foam
material from the interior of the saw. Now turn the adjuster clockwise
as far as it will go to raise the motor.
• Remove any remaining packing material from the saw.
Your saw was shipped with an anti-corrosion coating on the table top.
• Carefully clean the table top using a mild solvent cleaner.
Identifying the hardware parts (fig. B)
We recommend that you unpack and sort all hardware parts.
19 Allen key 5 mm
20 Blade wrench
21 Combination wrench
22 Torx wrench T50
23 Flat bracket
24 Front rail bracket
25 L-shaped bracket
26 Torx bolt T50, M10 x 30
27 Coach bolt M8 x 20
28 Hex head bolt M10 x 25
29 Hex head bolt M10 x 35
30 Hex nut M8
31 Hex nut M10
32 Wing nut
33 Flat washer M10
34 Lock washer M8
35 Lock washer M10
36 Wrench hook
Required and recommended tools
Apart from the tools included with the machine, the following tools are
required:
- Flat blade screwdriver
- Open end wrench 16 mm
- Ruler
- Set square
- Soft hammer (or regular hammer and block of wood)
You will also need:
- Mild solvent cleaner, eg. mineral spirits, paint thinner or denatured
alcohol
- High-quality paste wax
The following tools would be helpful:
- Socket wrench 16 mm
- Socket wrench 13 mm
- Open end wrench 10 mm
- Torx screwdrivers T20 and T25
- Torx wrench T40
Always use the correct type and size of tool.
Mounting the bevel adjuster (fig. C)
• Take the bevel adjuster (14) from the parts box.
• Place the adjuster onto the shaft (37). Slightly rotate the adjuster until
the shaft pin (38) engages in the slot (39).
• Screw the lock knob (40) onto the adjuster.
• Tighten the lock knob, then slacken it by half a turn.
Mounting the wrench hook (fig. D)
• Insert the wrench hook (36) into the hole (41).
• Thread the wrench hook in until only a few threads are still visible.
en - 4
All manuals and user guides at all-guides.com
Assembling the front rail (fig. E1 & E2)
Required hardware parts: 4 coach bolts (27), 4 front rail brackets (24),
4 lock washers (34), 4 nuts (30) (fig. E1).
Mounting the front rail to the saw (fig. F1 & F2)
Required hardware parts: 2 Torx bolts (26), 2 flat washers (33), 2 lock
washers (35), 2 nuts (31) (fig. F1).
Mounting the rear rail to the saw (fig. F3 & F4)
Required hardware parts: 2 L-shaped brackets (25), 2 short hex head
bolts (28), 2 long hex head bolts (29), 4 flat washers (33), 4 lock washers
(35), 4 nuts (31) (fig. F3).
Parallel the rails to the table top
Front rail (fig. F5)
Rear rail (fig. F6)
Always hang the combination wrench, blade wrench, push
stick and push block on the hook when not in use.
• Insert a coach bolt (27) into each of the front rail brackets (24)
as shown (fig. E2).
• Place a lock washer (34) and nut (30) onto the coach bolts and tighten
the nuts a few threads.
• Insert the head of the coach bolts into the keyhole slots (42) in the front
rail (11). Make sure that the brackets are pointing up (with the scale (43)
on the front rail facing up).
• Engage the square part of the bolts.
• Tighten the nuts finger tight.
• Hold the front rail against the front side of table top with the brackets
(24) pointing up (fig. F2).
• Align the upper holes (44) in the brackets with the corresponding holes
(45) in the table top.
• Insert a Torx bolt (26) into each of the holes in the brackets and the
table top.
• Place a flat washer (33), a lock washer (35) and a nut (31) onto the end
of each of the bolts.
• Tighten the nuts finger tight.
• Tighten the middle two rail bracket nuts (30).
• Mount 2 L-shaped brackets (25) for the outfeed table to the rear of the
table top using long hex head bolts (29), flat washers (33),
lock washers (35) and nuts (31) as shown (fig. F4). Make sure that the
brackets are at a right angle to the saw table.
• Align 2 holes in the rear rail with the lower holes in the brackets.
The flat side of the rail should be facing up.
• Mount the rail to the brackets using short hex head bolts (28),
flat washers (33), lock washers (35) and nuts (31) as shown.
Do not fully tighten.
• Use the fence face (5) to extend the table surface over the front rail (11).
• Using a ruler, measure the distance between the table top and the rail at
both ends of the table top. The distance should be equal at both ends.
• If adjustment is required, slacken the bolts (26) holding the brackets to
the saw. Tap the brackets using a soft hammer until the distances are
equal at both ends of the table top.
• Securely tighten the bolts.
• Use the fence face (5) to extend the table surface over the rear rail (12).
• Measure the distance between the table top and the rail at both ends
of the table top. The distance should be equal at both ends.
• If adjustment is required, slacken the bolts (29) holding the brackets to
the saw. Tap the brackets using a soft hammer until the distances are
equal at both ends of the table top.
• Securely tighten the bolts.
22