Silhouette DWC283BLS Manual Del Propietário página 5

OPERATION:
Before starting the w_ne cooler, ensure that the cabinet is Eeval
This witI eliminate any vibrations
NOTE: The power (RUN) indicator lfght is located en the LED
control panel inside the unff and illuminates
when the compressor (cooIing) cycle Is operatlonaI, turns off
when the compressor (cooi_ng) cycle is finished,,
SETTING THE TEMPERATURE CONTROLS: Each cooling
compartmentof the wine ceoter (upper & lower} are {ndependantly
conlrolted To set the temperature;
1, Connect the power cord to a properly grounded outlet In the
event of a power interruption, a{lprevious temperatureceilings are
aulomaticaliy erasedand each compartmentwili default |o a pre-
set temperalura setting of: t2 ° C (54" F)-Upper Compartment
6" C (43" F)-Lower Compartment
2 Set the desired coolingtemperature by pressing the butlons
adjacent to the "Set Upper/Set Lower" program Each depression
of the buttons wtlt scroll throughthe available temperature settings
(for each compartment) in incrementsof 1 degree, The
temperalure selected will flash in the LED disprayfor
approximately 5 seconds, then revert back to display the
temperature el the Internal cabinet
Upper Compartment: The tamperatura setting can be adjusted
from 10° O - 18_'C (50" F - 64" F}
Lower Compartment: The temperature setting can be adjusted
from 5° C - 10" C (41" F -50" F"}
3 To view the "sat" temperature, (anytime) press and hold the
corresponding button tot approximately 5 seconds, the "set"
temperature wilt temporadty "flash" tn the LED display for 5
aeconds.
Flashing LEO = Set Temperature
Steady LEO = Cabinet Temperature
===1
7 ¸
ii
LIMID(
..
_
4 This unit has the option to disptay temperatures in either Celsius
or Fahrenheit To change the setting, press and hold both buttons
(Set UppertSet Lower) s_mullaneously lot approximately 5
seconds, a prompt (beep) will sound and the blue pilot Itght
adjacent to the C or F mode Illuminates
NOTE: Te temporarily disconnect (stop) the cooling cycle, you
must disconnect the power cord from the electrical outlet NOTE;
There Is no "OFF"position on the e_ectronlc control panel
When disengaging cooling (operation) for long pedods of time,
leave the door patlially open to prevent mold/mildew from forming
inside the cabinet
NOTE: Always walt 3 to 5 minutes before restarting the unit If
operation has been tnterrupled,,
INTERtOR LIGHTS
The two(2) Interior lights operate "automatically" wtlh the
openinglclosing of the door The lig!lt turnson when the door is
open and turns off when the door is dosed
DEFROS'f INGtCONDENSATION
Your wine cootsris designed with an "Auto-Cycle" defrost system,
During lhe "Oil Cycle" the refrigeratedsurfaces of the wine cooler
(interior rear wail) defrost automatically The defrost water is
channeled Into a condensate drain pan which ts located at the
back of the wine cooter next to the compressor from where It
evaporates
CARE & MAINTENANCE
Upon receivingyour winecooler, leave the door open for 24 hours
When cleaningthe Inside of the wine cooler you can use a solution
of a tablespoonel baking soda to one (f) quart of water, or a mild
soap suds solution,or some mild detergent Wood shefving does
not require cleaning, To clean the exterior cabinetof your wine
cooler, use a soft damp cloth with mild detergent or apptlance
cleaner
STORAGE OF WINE
The upper compartment }s for stodng "Red" wine (10 BolUs
Capacity + Humidor)
The lower compartmentts for stodng "White"wine (20 Bottle
Capacity + Humidor)
The hum}dot should be positioned In the center of the top rack _n
each compartment,
To achieve maximum storage capacity it will be necessary to
position (s!ora) the bottles alternately on the racks (sea below
diagram)
HUMIDITY MAINTENANCE SYSTEM
The wine cooler is equipped with a system for
maintaining the correct level of humidity If humidity is
too row, insert the small plastic reservoir on to the top
rack of the wine cooler, r Fill this reservoir 3/4 full with
wate_t Check water level occasionally and refill as
necessary