Descargar Imprimir esta página

KPS PA700 Manual De Instrucciones página 2

Pinza amperimétrica digital

Publicidad

Idiomas disponibles

Idiomas disponibles

ENGLISH
Description
• The meter is a portable, professional measuring instrument with LCD display and backlight
for easy reading by users. Measuring range switch is operated by single hand for easy
operation with overload protection and low battery indicator. It is an ideal multifunction
meter for professionals, factories, schools, fans and family use.
• The meter is used to measure AC current , AC voltage, DC voltage, frequency, duty ratio,
resistance, capacitance measurement, temperature, NCV and circuit connection, and to
make diode tests.
• The meter has an aut o measuring range function.
• The meter has a tested at a dual display function.
• The meter has a reading hold function.
• The meter has a relative test function.
• The meter has max. and min. display function.
• The meter has a manual measuring range selection function.
• The meter has a backlight function.
• The meter has a auto power-off function.
SAFETY INFORMATION
WARNING
Be extremely careful when using this meter. Improper use of this device can result in
electric shock or destruction of the meter. Take all normal safety precautions and follow
the safeguards suggested in this manual. To exploit full functionality of the meter and
ensure safe operation, please read carefully and follow the directions in this manual. If the
equipment is used in a manner not specified by the manufacturer, the protection provided
by the equipment may be impaired.
This meter is designed and manufactured according to safety requirements of EN 61010-1, EN
61010-2-032, EN 61010-2-033 concerning electronic measuring instruments with a measurement
CAT III 1000V and pollution degree 2 and safety requirements for hand-held clamps for electrical
measurement and test.
Preparation
• When using the meter, the user should comply with standard safety rules:
- General shock protection.
- Prevent misusing the meter.
• After receiving the meter, please check for damage that may have occurred during the
transport .
• If the meter is store and shipped under hard conditions, please confirm if the meter is
damaged.
• Probe should be in good condition. Before use, please check whether the probe insulation
is damaged and if the metal wire is bare.
• Use the probes provided with the meter to ensure safety. If necessary, replace the probe
with another identical probe or one with the same specification.
Usage
• When using, select the right function and measurinq range.
• Don't exceeding indicated values in each measuring range.
• When measuring circuits with the meter connected, do not touch the probe tip (metal part).
• When measuring, if the voltage to be measured is more than 60 V DC or 30 V AC (RMS),
always keep your fingers behind the finger protection device.
• Do not measure between measuring end and ground that is more than 1000V DC or
750V AC.
• Far manual measuring range, when the value to be measured is unknown in advance,
choose the highest measuring range first and then lower ranges in sequence until the
correct range is found.
• Befare rotating selector switch to change measuring function, remove the probe from the
Don't measure resistors, capacitors, diodes and circuits connected to power.
• During the test of current, resistors, capacitors, diodes and circuit connections, be careful
to avoid connecting the meter with the voltage source.
• Do not measure capacitance befare capacitar is discharged completely.
• Do not use the meter in explosive gas, vapor or dusty environments.
• lf you find any abnormal phenomena or failure on the meter, stop using the meter.
• Unless the meter bottom case and the battery cover are completely fastened completely,
do not use the meter.
• Don't store or use the meter n direct sunlight, high temperature or high humidity.
MAINTENANCE
• Don't try to open the meter bottom case to adjust or repair. Such operations can only be
performed by technicians who fully understand the meter and electrical shock hazard.
• Before opening the meter bottom case or battery cover, remove probe from the circuit to
be measured.
• To avoid wrong readings causing electric shock, when
replace the battery immediately.
• Clean the meter with damp cloth and mild detergent . Do not use abrasives or solvents.
• Power off the meter when the meter is not used. Switch the measuring range to OFF
position.
• If the meter is not used for long time, remove the battery to prevent the meter being
damaged.
Replace battery
WARNING
To avoid electric shock, make sure that the test leads have been clearly move away from
the circuit under measurement before opening the battery cover.
1. If the symbol
, appears, it means that the batteries should be replaced.
2. Loosen the screw of the battery cover and remove it.
3. Replace the used battery with a new one.
4. Return the battery cover and tighten the screw.
Note: The battery polarity can't be reversed.
ENG
ENGLISH
Replace Probe
Replace test leads if leads become damaged or worn.
Use meet EN 61010-031 standard, rated CAT III 1000V, or better test leads.
To avoid electric shock, make sure the probes are disconnected from the measured cir-
cuit before removing the rear cover. Make sure the rear cover is tightly screwed before
using the instrument.
ACCESSORIES
• Test probe
• K-Type temperature probe
• Summary instruction manual
• 9V DC battery (6FF2)
• Case
appears on the meter display,
APAC: MGL GLOBAL SOLUTIONS LTD
info.apac@mgl-intl.com
Flat 4-1, 4/F, No. 35, Section 3 Minquan
East Road. Taipei, Taiwan.
Tel: +886 2-2508-0877
EMEA: MGL EUMAN S.L.
info.emea@mgl-intl.com
Parque Empresarial Argame, 33163
Morcín. Asturias, Spain.
Tel: +34 985-08-18-70
Digital clamp meter
WARNING
WARNING
1 pair
1 pc.
1 pc.
1 pc.
1 pc.
See the full
instruction manual:
AMERICAS: MGL AMERICA, LLC.
info.na@mgl-intl.com
US East Coast: 2810 Coliseum Centre
Drive, Ste. 100. Charlotte, North Carolina,
28217 USA
MGL EUMAN, S.L.
Tel: +1 833 533-5899
Parque Empresarial de Argame,
US West Coast: 760 Challenger Street.
C/Picu Castiellu, Parcelas i-1 a i-4
Brea, California 92821 USA
E-33163 Argame, Morcín
Tel: +1 310-728-6220
Asturias, España, (Spain)
www.mgl-intl.com
ENG

Publicidad

loading

Este manual también es adecuado para:

Kpspa700cbint