Tabla De Contenido; General Description; Operation; Setup - Titan 440 Manual Del Propietário

Table of contents
Safety Precautions ................................................................... 2
Specifications ........................................................................... 3
General Description ................................................................. 4
Operation ................................................................................... 4
Setup ................................................................................... 4
Preparing to Paint................................................................ 5
Painting ............................................................................... 5
Control Panel Indicators ...................................................... 6
Pressure Relief Procedure .................................................. 6
Spraying .................................................................................... 7
Spraying Technique ............................................................ 7
Practice ............................................................................... 7
cleanup ..................................................................................... 8
Maintenance .............................................................................. 8
General Repair and Service Notes...................................... 8
Replacing the Motor ............................................................ 9
Replacing the Gears............................................................ 9
Replacing the Transducer ................................................. 10
Replacing the PRIME/SPRAY Valve ................................. 10
Servicing the Fluid Section ................................................ 11
Replacing the Filters.......................................................... 12
Troubleshooting ..................................................................... 13
Parts Listings .......................................................................... 38
Main Assembly .................................................................. 38
Siphon Assembly (skid model) .......................................... 40
Skid Assembly ................................................................... 40
Drive Assembly ................................................................. 41
Fluid Section Assembly ..................................................... 42
Cart Assembly ................................................................... 44
Labels ................................................................................ 44
Electrical Schematic .......................................................... 45
Accessories ....................................................................... 45
Warranty .................................................................................. 48

General Description

This airless sprayer is a precision power tool used for spraying
many types of materials. Read and follow this instruction manual
carefully for proper operating instructions, maintenance, and
safety information.
Siphon
Tube
Motor
ON/OFF
Switch
Filter
Pressure
control
knob
Pusher stem

Operation

This equipment produces a fluid stream at extremely
high pressure. Read and understand the warnings
in the Safety Precautions section at the front of this
manual before operating this equipment.

Setup

Perform the following procedure before plugging in the power
cord of an electric unit.
1. Ensure that the siphon tube and the return hose are
attached and secure.
English
2. Using a wrench, attach a minimum of 50' of 1/4" airless
3. Attach an airless spray gun to the spray hose. Using two
NOTE: Do not attach the tip to the spray gun yet.
4. Make sure the pressure control knob is in its OFF position
5. Make sure the ON/OFF switch is in its OFF position.
6. Remove the fill cap with a straight-slot screwdriver, or a
7. Press oiler button 2-5 times to prime the oiler. Press once
IMPORTaNT: Never operate unit for more than ten seconds
without fluid. Operating this unit without fluid will cause
unnecessary wear to the packings.
8. Fully depress the pusher stem to make sure the inlet ball
9. Make sure the electrical service is 120V, 15 amp
10. Plug the power cord into a properly grounded outlet at
IMPORTaNT: always use a minimum 12 gauge, three-wire
extension cord with a grounded plug. Never remove the
third prong or use an adapter.
Preparing a New Sprayer
Return If this sprayer is new, it is shipped with test fluid in the fluid
Hose
section to prevent corrosion during shipment and storage. This
fluid must be thoroughly cleaned out of the system with mineral
Oiler
spirits before you begin spraying.
Cap
IMPORTaNT: always keep the trigger lock on the spray gun
in the locked position while preparing the system.
Oiler
button
1. Place the siphon tube into a container of mineral spirits.
2. Place the return hose into a metal waste container.
PRIME/
3. Set the pressure to minimum by turning the pressure
SPRAY
Valve
Fluid
Section
Outlet Fitting
(black zone)
Turbo PulseClean
4. Move the PRIME/SPRAY valve down to the PRIME position.
5. Turn on the sprayer by moving the ON/OFF switch to the
6. Allow the sprayer to run for 15-30 seconds to flush the
7. Turn off the sprayer by moving the ON/OFF switch to the
4
spray hose to the outlet fitting on the sprayer. Tighten
securely.
wrenches (one on the gun and one on the hose), tighten
securely.
Remove the tip if it is already attached.
Make sure all airless hoses and spray guns are
electrically grounded and rated at or above the
maximum operating pressure range of the airless
sprayer.
in the black zone.
coin. Fill the oil reservoir with one ounce of piston seal
lubricant (Piston Lube). Replace oiler cap.
for every eight hours of usage to lubricate the fluid section.
is free.
minimum.
least 25' from the spray area.
control knob to the "MIN" setting.
Pump OFF
ON position.
test fluid out through the return hose and into the waste
container.
OFF position.
© Titan Tool Inc. All rights reserved.
Pressure
Indicator
Pressure
Control Knob