Hoover Sprint Evo Manual Del Usuario página 4

USING YOUR CLEANER
Extract power cord and plug it into the power supply. [5] Do not pull the cord beyond the
1.
red marker.
Adjust the telescopic tube* to the desired height by moving the telescopic tube adjuster up
2.
and raise or lower the handle to the most comfortable cleaning position. [6]
Carpet & Floor Nozzle**. Press the floor type selector pedal on the nozzle [7] to select the
3.
ideal cleaning mode for the floor type.
hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
Switch the cleaner on by pressing the On/Off button on the cleaner main body. [8]
4.
Vary the suction as desired by closing or opening the suction regulator* on the hose
5.
handle. [9]
Switch off at the end of use by pressing the On/Off button. [8] Unplug and press the cord
6.
rewind button to wind the power cord back into the cleaner. [10]
To store your cleaner, park the nozzle in the parking slot at the rear of the cleaner main
7.
body. [11]
ACCESSORIES
All accessories can be fitted to the hose handle or the end of the tubes.
2 in 1 Tool combines several functions into one tool:
Crevice Tool – For corners and hard to reach areas. [12]
dusting Brush – For bookshelves, frames, keyboards and other delicate areas. [13]
Pet hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs
removal. [1X]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal. [1Y]
hard Floor Nozzle* – For parquet floors and other delicate floors. [1Z]
IMPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.
* Certain models only
** May vary depending on model
SprintEvoManual__1-3_union.indd 2
CLEANER MAINTENANCE
Emptying the dust Container
when the dust reaches the max level indicator on the container, empty the dust container.
IMPORTANT: To maintain optimum performance, do not allow the dust to sit higher than the
max level.
1. Release the dust container by sliding the dust container release button towards the front
of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Before emptying the Dust Container, gently tap it against the side of a bin to release any
excess dust from the filter.
3. To empty the Dust Container, hold the Dust Container over a bin with one hand and use
the other hand to press the Dust Container Flap Opening Button to release the dust into
the bin. [15]
4. Close the Dust Container Flap and refit the Dust Container to the cleaner main body.
Cleaning the Washable Filters
The cleaner is fitted with a pre-motor and exhaust filter. To maintain optimum cleaning
performance, regularly clean the filters. Remove excess dust from the filters by gently tapping
them against the side of a bin. The filters should be washed after every 5 container empties.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean your
filters may result in air blockage, overheating and product failure. This may invalidate
your guarantee.
IMPORTANT: Regularly check and maintain the filters by following the filter maintenance
instructions, it is also recommended that you purchase new filters after every 3rd filter
wash. This will maintain your cleaners performance.
To access the pre-motor filter:
1. Empty the Dust Container as described in 'Emptying the Dust Container' . Then, keeping
the Dust Container Flap open:
2. Remove the pre-motor filter by rotating it clockwise at the bottom of the Dust Container.
[16]
3. Separate the protective mesh from the filter. [17] Gently tap both the protective mesh
and the filter against the side of a bin to remove excess dust and wash both of them
under warm water. [18] Do not use hot water or detergents.
4. Remove excess water from the filter and leave it to dry fully before reusing. [21]
5. Once the filter is fully dry, reassemble the filter pack (protective mesh and filter) and refit
to cleaner.
6.
IMPORTANT: Do not use the product without the pre-motor filter pack fitted.
IMPORTANT: Always ensure the filter packs are fully dry before use.
2
GB
25/07/2012 13.49.55