Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY ISSUES REMARKS
1.
Nozzles should be installed without the use of excessive force, also do not use the pliers or tweezers.
Do not over tighten the mounting screws of the nozzle.
2.
Tips and nozzles can be changed when the HOT AIR gun and the soldering iron are completely cold.
3.
It is forbidden to use the device near the flammable or combustible elements and objects or in simi-
lar places. Tips and nozzles as well as the air coming out of the HOT AIR gun have very high tempera-
tures, it is forbidden to touch these elements as well as it is forbidden to direct the hot air at face or
body. This can cause serious burns.
4.
After long time of use, the outlet of HOT AIR gun may be covered with some dust. The outlet should
be cleaned on a regular basis in order to ensure undisturbed air flow.
5.
Too high temperature of the soldering iron may be the cause of reduction of the functionality of the
soldering tips.
6.
Soldering iron tip must be cleaned regularly using sponge and plate on a layer of tin to prevent tips
oxidation.
REPLACEMENT OF HOT AIR REWORK HEATING ELEMENT
1.
HOT AIR gun covers
2.
element of the handle
3.
heater
4.
heater cover
1
5.
outlet pipe
2
6.
nozzle
3
Before heater replacement make sure that the HOT AIR gun is completely cold.
Remove the screws in the gun covers.
4
Unscrew the element of the handle (2) and take off the gun covers.
Gently remove the fan and remove the wire board screws.
5
Disconnect the heater from the wire board (pay attention to the wires
connection order).
6
Remove the heater from the housing, pay attention to the steel grounding wire.
New heater should be wrapped with new mica paper and then it should be
placed inside the housing.
14
EN
REPLACEMENT OF THE SOLDERING IRON TIP AND SOLDERING IRON HEATING
CORE ELEMENT
5
4
3
2
1
8
7
6
BEFORE HEATER REPLACEMENT MAKE SURE THAT THE SOLDERING IRON IS
COMPLETELY COLD.
1. SOLDERING IRON TIP REPLACEMENT: remove the nut for mounting the soldering iron tip housing
and take off the housing. Replace the tip with the new one, place the housing and fix all with the plastic nut.
2. HEATER REPLACEMENT: remove the nut for mounting the soldering iron tip housing and take off the
housing along with the tip. Remove the nut for fixing the heater (4) and gently remove the heater (6) along
with the board with wires (7). Replace the whole remembering the wires connection order.
REGULAR CLEANING
Generalities
•
Never clean the device with a pressurized water-jet, industrial cleaners, and brushes or any other
type of cleaning utensil that could damage the surface of the appliance.
•
Before cleaning you must remove the electricity supply plug isolating the appliance from the main
power circuit.
REGULAR CONTROL OF THE DEVICE
Control regularly that the device doesn´t present any damage. If there is any damage, please stop using the
device. Please contact your customer service to solve the problem.
What to do in case of problem?
Please contact your customer service and prepare following information:
•
Invoice number and serial number (the latest is to be found on the technical plate on the device).
•
If relevant, a picture of the damaged, broken or defective part.
•
It will be easier for your customer service clerk to determine the source of the problem if you give
a detailed and precise description of the matter. Avoid formulations like "the device doesn´t heat",
which may mean that it doesn´t heat enough or even not at all. These two possibilities have a different
causation!
•
The more detailed your information, the better the customer service will be able to answer your
problem rapidly and efficiently!
CAUTION: Never open the device without the authorization of your customer service. This can lead to a
loss of warranty!
EN
DE
1.
nut for mounting the soldering iron tip
housing
2.
soldering iron tip housing
3.
soldering iron tip
4.
plastic nut for mounting the heater and
the board wires
5.
spring
6.
heater
7.
wires board
8.
handle
15
Publicidad
Tabla de contenido
