FITFIU FITNESS GYM-200 Manual Del Usuario página 17

STEP 5
1. Attach the pull unit (09) to the bridge tube
(08), insert the pull unit axle (21) through 2
metal bushings (31A) and secure using 2
washers (36) and 2 nuts (40).
2. Attach the right-hand butterfly arm (10R)
to the right side of the pull unit (09) through
2 metal bushings (31) and secure using 2
washers (36) and 1 nut (40). Perform the
same procedure to attach the left-hand
butterfly arm (10L) to the pull unit (09).
3. Insert the rubber stop (52) to the bracket on
the upright support tube (05), then adjust the
pull unit (09) to match the hole in the bracket.
4. Place the butterfly arm pads (53) onto the
butterfly arms (10R and 10L), then insert a
50mm flat cap (46) to the ends of the butterfly
arms.
5. Attach a handlebar (11) to the right-hand
butterfly arm (10R) and secure using 3 bolts
(22) and 3 washers (33). Perform the same
to attach the handlebar (11) to the left-hand
butterfly arm (10L).
6. Attach the pulley bracket (20) to each side of
the main support tube (05) and secure using 2
bolts (23), 4 washers (35) and 2 nuts (39).
STEP 6
1. Attach the lat bar cable (65) to the opening
bracket at the front of the bridge tube (08).
Note: The ball stopper of the cable should be
underneath the bridge tube. Run cable (65)
over the small pulley (49A) and put a small
pulley cover (50) on each side of the pulley.
Note: Cable (65) has to come out of the pulley
covers (50) through the opening. Secure pulley
(49A) to the bracket using 1 bolt (26) and 1 nut
(39).
2. Pull cable (65) towards the back of the
machine through the upper opening in the
main support tube (05) and around the first
pulley (49), then attach this pulley to the
bridge tube (08) bracket and secure using 1
bolt (25) and 1 nut (39).
3. Pull cable (65) downwards and around the second pulley (49). Attach this pulley to
the main support tube (05) using the pulley bracket (17), 1 bolt (25) and 1 nut (39).
4. Pull cable (65) upwards and around the third pulley (49). Attach this pulley to the
bridge tube (08) bracket and secure using 1 bolt (25) and 1 nut (39).
5. Pull cable (65) downwards and fully screw in the bolt on the end of the cable to the top
of the weight bar (19).
6. Attach the lat bar (12) to the front end of cable (65), and secure using 1 X1 hook (62).
32
STEP 7
1. Attach one end of the butterfly arm cable
(66) to the hook on the right-side butterfly
arm (10R) and secure using 1 bolt (24), 1
washer (35A) and 1 nut (38).
2. Pull cable (66) around the upper pulley (49),
then attach this pulley to the pulley bracket
(20) on the righthand side of the main
support tube (05) and secure using 1 bolt
(25) and 1 nut (39).
3. Loop cable (66) around the lower pulley (49),
then attach this pulley to the upper part of
the two-way pulley bracket (18) and secure
using 1 bolt (25) and 1 nut (39).
4. Pull cable (66) upward and around the
second upper pulley (49), then attach this
pulley to the pulley bracket (20) on the left-
hand side of the main support tube (05) and
secure using 1 bolt (25) and 1 nut (39).
5. Attach the other end of cable (66) to the
hook on the left-side butterfly arm (10L) and
secure using 1 bolt (24), 1 washer (35A) and
1 nut (38).
STEP 8
1.
2.
3.
GYM-200
Place the cable guides (69) on either side of the small pulley
(49A) as shown, and secure using 1 bolt (26) and 1 nut (39).
Pull the NON-stopper-ball end of the lower pull bar cable (67)
through the opening at the bottom of the leg curl tube (06),
around the undersides of pulley (49) and small pulley (49A).
Then pull the cable through the opening in the lower part of
the upright support tube (02), then around the underside of
pulley (49) in the seat support tube (04). Pull the cable upward
and around the upper side of a pulley (49), then attach this
pulley to the underside of the two-way pulley bracket (18) and
secure using 1 bolt (25) and 1 nut (39).
Pull cable (67) downward and around the underside of a pulley
(49), then attach this pulley to the bracket on the end of the
seat support tube (04) and secure using 1 bolt (25) and 1 nut
(39).
4. Pull cable (67) upward and around the
upper side of a pulley (49), then attach
this pulley to the lower section of the
pulley bracket (17) and secure using 1
bolt (25) and 1 nut (39).
5. Pull cable (67) downward and connect
it to the bracket on the rear stabilizer
(03) using chain (61) and 1 X1 hook (62).
Note: Hook the cable to a chain link that
causes it to be taught.
6. Attach the lower pull bar (13) to the front
end of cable (67) using chain (61) and 2
X1 hooks (62).
33
EN