FITFIU FITNESS GYM-200 Manual Del Usuario página 49

STEP 2
1. Push the weight cushion (#43) and the weight stack (#37) one after the other through the guide rods (#6).
NOTE: Carefully slide the weight plates onto the guide rods one at a time, do not lift more than
you can safely control.
2. Place the weight bush (#38) on the
weight selection rod (#41) and secure
it with the weight pin (#39) in the first
hole of the weight selection rod (#41).
Insert the rod (#41) into the hole of
the weight discs (#37). Slide the upper
weight plate (#36) into the weight
stack. Place the weight disc (#40) in the
hole in the upper weight plate (#36).
3. Slide the upper cover bracket (#89)
through the guide rods (#6).
4. Insert the Ø60 connector (#49) into
part (#3). Attach part(#3,#25) to
part(#2) with (2)M10*80 hexagon (#86),
(2)M10 nylon lock nuts(#68) and (4)Ø10
arc washers(#77).
5. Grasp each of the guide rods (#6) in the
holes of the part (#3) and then connect
the part (#3, #89) to the guide rods (#6)
with (2)M10*30 hex bolts (#52) and (2)
Ø10 washers (#73).
STEP 3
1. Insert the plug Ø38(#51) and the end cap
Ø38(#54) into part(#5) one after the other.
2. Fix part(#5) to part(#2) with (1)hexagon
bolts M10*80(#86), (2)nylon lock nuts
M10(#68) and (3)shackle washers
Ø10(#77).
3. Attach part(#17) to part(#5) with (1)hex bolt
M8*45(#81), (1)nylon lock nut M8(#67) and
(2)washers Ø8(#72). Screw the plastic nut
(#56) onto part(#17).
4. Attach part(#20) to part(#2) with (2)
hexagon bolts M10*65(#85), (2)nylon lock
nuts M10(#68) and (4)washers Ø10(#73).
5. Attach part(#28) to part(#2) with (2)
hexagon bolts M8*80(#82) and (2)washers
Ø8(#76).
96
STEP 4
1. Attach part(#7,#25) to part(#2) with (2)hexagon bolts M10*80(#86), (2)nylon lock nuts M10(#68) and (4)
shackle washers Ø10(#77). Insert the sleeve (#59) into the part (#7). Screw the knob (#57) to the part (#7).
2. Fix part (#29) to part (#9) with (4)hexagon screws M6*20(#79) and (4)washers Ø6(#71).
3. Pass part(#9) through sleeve(#59), adjust to the desired height and loosen knob(#57) to fix part(#9).
4. Insert the plug Ø60(#49) into part(#8), then fix part(#8) to part(#7) with (1)hexagon bolt M12*85(#75), (1)
nylon lock nut M12(#69) and (2)washers Ø12(#74).
NOTE: Tighten the screw (#75) and loosen the nut enough so that the part (#8) can turn freely.
Put the pin with the ring (#62) through the first hole of part (#7) to lock part (#8).
5. Insert the plug Ø25(#53) into the end of part(#22), then pass part(#22) through part(#7,#8) as shown in the
picture. Push the foam roller Ø80*160(#47) into the part(#22).
6. Put the hexagon nut cap (#44) on the bolt (#75) and the nut (#69). Put the hexagon nut cap (#44) on the
bolt (#75) and the nut (#69).
GYM-200
97
EN