Delivery Contents; Installation Options; Technical Data - Etac Relax Manual

Etac / Relax / www.etac.com
General
Thank you for choosing a shower chair from Etac. To avoid injury during
installation, handling and use, please ensure that you read this manual
thoroughly and keep it. It can also be downloaded from www.etac.com.
Here you will also find other documentation such as pre-sale information,
pre-purchase guide and reconditioning instruction.
The Etac Relax is a wall-mounted shower seat designed as a seating
and standing support for personal hygiene purposes for people with
reduced mobility. The Etac Relax shower seat is used for sitting where
space is restricted, and can be folded up when not in use. The Etac Relax
shower seat with support legs is recommended for users weighing more
than 125 kg (max. 150 kg). The Etac Relax shower seat with armrests is
recommended wherever users need support to stand up. The backrest is
attached to the wall above the seat and is recommended for users who
need back support.
Etac Relax is intended for home use.
Etac Relax is not designed to be used in any other way than described
above.
Etac Relax has been tested by test institutes and complies with the require-
ments set out in EN ISO 10993-1, SS EN 12182.
Etac Relax is CE marked according to Directive 93/42/EEC on medical
devices.

Delivery contents

See figure A

Installation options

Etac Relax has been designed to withstand a maximum vertical static load
of 125 kg (150 kg with support legs) and should only be mounted on a
wall with sufficient load-bearing capacity. Ensure you use suitable fixtures.
Etac recommends Relax accessories; a screw set for mounting on wood/
plywood or concrete walls.
Both the mounting of the seat and assessment of the wall and fixtures'
load-bearing capacity should be carried out by a qualified person.
In the case of other wall materials, or if the load-bearing capacity of the
wall is deemed insufficient for any reason, the wall can be reinforced by a
qualified person.
Mounting on a wall with insufficient load-bearing capacity or
unsuitable fixtures poses a danger to the user!
Installation
1. Installation on uncracked concrete C20/25 up to C50/60. Always mount
using Fischer UX R 10 plugs.
2. Mounting on wood or plywood (min. 12 mm) with partition wall (min.
12 mm).
Usage
See figure C
All manuals and user guides at all-guides.com
English
Figure A
Figure B
Figure C
10
Maintenance and safety
1. Clean/disinfect the chair with normal non-abrasive cleaning agents with
a pH value of between 5-9, or with 70% disinfectant solution. Rinse
and dry.
The product is otherwise maintenance-free.
2. The product can withstand cleaning in a sterilizer at 85°C for 3 minutes.
This applies for reconditioning.
3. Maximum user weight (see technical data).
4. Do not stand on the shower chair!
5. Please ensure that both legs are resting against the floor when folding
down the shower chair.
6. Check that the bolts are securely tightened. Defective or incorrectly
installed products must not be used. In case of damage, contact your
dealer.
7. Risk of crushing!
8. The armrests have each been tested and approved for half of the
maximum user weight.
9. Heated chair can cause burns.
The materials used are corrosion-resistant.
The materials used are resistant to all general disinfectants.
For reconditioning and reuse, see the reconditioning instructions on www.
etac.com.
Guarantee, service life
5-year guarantee against material and manufacturing defects. For terms
and conditions, see www.etac.com.
The product's durability and lifetime is at least 5 years when used in
accordance with intended use, the safety instructions, the reconditioning
manual and instructions for use in the user manual. The actual lifetime
can vary, depending on how much and how intensively the product is
being used, but a maximum of 10 years. Thereafter the product must be
decommissioned.
Accessories
1. Support legs
3. Screw set for wood/plywood and
concrete.
Label placement
1. Product label (warnings, CE-marking)
2. Item no label (serial no, production date)

Technical data

See figure G
This product should be recycled as per national regulations.
See material specification for sorting (Figure G)
Figure D
Figure E
2. Back support
Figure F
Figure G