Declaration Of Conformity; Images; Technical Characteristics; The Overall Machine - Rubi DCX-250 XPERT Manual Del Usuario

PARALLELISM
65) To adjust the parallelism of the blade, it is necessary to use an alignment
device as a reference.
a) Position the component so that the protrusion on the alignment device
touches the outermost face of the blade at the front. To do this, rotate
the blade until it comes into contact, you will notice a slight noise when
the blade comes into contact with the protrusion. Mark that point as a
reference (fig. 29).
b) Move the blade head, without changing the position of the alignment
device (fig. 30) and turn the blade again to the indicated mark. If the
blade does not make contact at the same point, it will be necessary to
adjust the parallelism of the blade.
c) You can adjust the position of the motor by rotating it slightly.
d) Loosen screws A as indicated and rotate the motor using transversal
screw B. Repeat the same procedure and make sure that in both positions
the blade makes contact with the alignment device (fig. 31, 32).
e) Once the blade is positioned, retighten screws A.
ADJUSTMENT/LEVELLING OF THE MACHINE:
66) The DCX Xpert machine has a levelling foot to adjust the position of the
chassis. This should be used to adjust and stabilise the machine on the
ground. For a good finish, work on flat surfaces.
a) Unscrew locknut A to release the levelling foot (fig. 33)
b) Adjust (by screwing or unscrewing nut B) the levelling foot to eliminate
any play that may occur in the legs. Retighten locknut A to secure the
system (fig. 34).
If you have any doubts about the functioning of the machine or its
adjustment, please contact our after-sales service.
STORAGE
Store the tool in its packaging in a cool, dry place protected against cold and
direct sunlight.
The machine must be put out of service and dismantled in accordance with
the instructions in each country, at a selective collection point for the proper
classification and processing of the materials.
AFTER-SALES SERVICE
Use only original spare parts supplied by the manufacturer. Repairs should
only be done by certified workshops or RUBI's technical service:
GERMANS BOADA SANTA OLIVA
Ronda de l'Albornar, 24-26
43710 Santa Oliva, Tarragona (Spain)
Tel: +34 977 16 90 50
For more information and the location of RUBI's official technical
support centres visit: https://www.rubi.com/es/servicio-post-venta

4. DECLARATION OF CONFORMITY

The company, Germans Boada S.A Avda. Olimpíades 89-91, P.O Box 14
-08191 Rubi (Barcelona, Spain), declares, under its sole responsibility, that
the machine:
Complies with the following standards:
o EN ISO 12100:2010; EN 12418:2000+A1:2009
o EN 61029-1:2009+A11:2010; EN 60204-1:2006/AC:2010
o EN 61000-6-4:2007+A1:2011; EN 61000-6-2:2005
o EN 61000-3-3:2013; EN 61000-3-2:2014
And complies with the essential requirements of the following
directives:
o 2006/42/EC MACHINERY DIRECTIVE/ANNEX VIII
o 2014/35/EU LOW VOLTAGE DIRECTIVE
o 2014/30/EU ELECTROMAGNETIC COMPATIBILITY DIRECTIVE
At Rubi, 15/01/2021
Carles Gamisans Berenguer
R&D Director
· TRANSLATION OF THE ORIGINAL · ENGLISH

5. IMAGES

6. TECHNICAL CHARACTERISTICS

7. THE OVERALL MACHINE

8. CABLE WITH PLUG

9. ACCESSORIES

10. ELECTRICAL CIRCUIT

11. VIBRATION TEST

12. WARRANTY

The reproduction of the work, in whole or in part, in any format or by any
means or procedure, whether mechanical, photographic or electronic,
without the prior authorisation of GERMANS BOADA, S.A. is prohibited.
Any of these activities shall incur the corresponding legal liabilities and
could result in criminal prosecution.
GERMANS BOADA, S.A. reserves the right to make any technical
modification without prior notice.
PAGE 100
PAGE 104
PAGE 105
PAGE 105
PAGE 105
PAGE 106
PAGE 107
PAGE 109
- 11 -