Intended Use; Assembly And Adjustments - Craftsman CMEHTS822 Manual De Instructiones

English

CAUTION:
on its side on a stable surface where it will not
cause a tripping or falling hazard. Some tools will
stand upright but may be easily knocked over.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.
• An extension cord must have adequate wire size
(AWG or American Wire Gauge) for safety. The smaller
the gauge number of the wire, the greater the capacity
of the cable, that is, 16 gauge has more capacity than 18
gauge. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. When using
more than one extension to make up the total length,
be sure each individual extension contains at least the
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V 25 (7.6)
240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More not
Than More
Than
0 6 18
6 10 18
10 12 16
12 16 14
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
OPM .................... oscillations per
minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
or AC/DC .... alternating or
direct current
4
When not in use, place tool
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
American Wire gauge
16 16
16 14
16 14
12 Not Recommended
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... avoid staring at
light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
IPXX .................... IP symbol
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.

Intended Use

This hedge trimmer is designed for residential use.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.

ASSEMBLY AND ADJUSTMENTS


WARNING:
serious personal injury, turn unit off and
disconnect it from power source before making
any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
Assembly Tools Required
• Crosshead Screwdriver
Attaching Guard and Bail Handle to
Trimmer (Fig. B, C, D)
14

WARNING:
12
12
guard properly assembled to hedge trimmer. The use
of the hedge trimmer without the proper guard or
handle provided may result in serious personal injury.
The trimmer is shipped with the guard and bail handle
attached to the trimmer with a plastic zip tie.
To Assemble to Trimmer
1. Cut the plastic zip tie.
2. Remove the six screws that are partially run into the
trimmer housing (Figure B).
3. Slide the guard onto the front of the trimmer housing.
4. Insert two of the six screws into the openings on the
side of the guard and tighten securely as shown in
Figure C.
5. Slide the bail handle onto the front of the trimmer
housing behind the guard.
6. Insert the remaining four screws into the openings
on the side of the bail handle and tighten securely as
shown in Figure D.
To reduce the risk of
Only use with handle and