Service Air Cleaner; Service Spark Plug - Craftsman 580.750901 Manual Del Operador

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Change oilwhile
engine is still warm from running, as
follows:
1.
Drain fuel tank by running pressure washer until fuel
tank is empty.
2.
Disconnect spark plug wire and keep it away from spark
plug.
3.
Cleanarea around oil fill, remove oil fill cap/dipstick.
Wipe dipstick clean.
4.
Tip your pressure washer to drain oil from oil fill into a
suitable container making sure you tip your unit away
from spark plug. When crankcase is empty, return
pressure washer to upright position.
5.
Slowly pour recommended oil (about 18 oz.) into oil fill
opening. Pauseto permit oil to settle. Fill to FULL mark
(top hob) on dipstick.
6.
Wipe dipstick clean each time oil level is checked. DO
NOT overfill.
7.
Replace and tighten dipstick.
8.
Wipe up any remaining oil.
9.
Reconnect spark plug wire to spark plug.
Service Air Cleaner
Your engine will not run properly and may be damaged if you
run it with a dirty air cleaner. Service more often if operating
under dirty or dusty conditions. Replacementsare available
at your local Sears service center.
Te service the air cleaner, feiiew these steps:
1.
Remove screw (A).
.
3.
.
5.
6.
Carefully remove air cleaner assembly to prevent debris
from falling into carburetor.
Take air cleaner assembly apart and clean all parts.
Wash foam air cleaner (B) in liquid detergent and water.
Squeezedry in a clean cloth.
SATURATE foam air cleaner in engine oil and squeeze in
a clean cloth to remove excess oil.
Reinstall clean or new foam air cleaner in base (C).
Install air cleaner securely on carburetor with screw.
Service Spark Plug
Changingthe spark plug will help your engine to start easier
and run better.
1.
Clean area around spark plug.
2.
Removeand inspect spark plug.
3.
Replacespark plug if electrodes are pitted, burned or
porcelain is cracked. Use the recommended replacement
plug, See Specifications,
4,
Check electrode gap with wire feeler gauge and reset
spark plug gap to recommended gap if necessary (see
Specifications),
5.
Install spark plug and tighten firmly.
NOTICE You can purchase a new spark plug by calling
1-800-4-IVIY-N01VlE (469°4663).
MnspectNluffier and Spark Attester
inspect the muffler for cracks, corrosion, or other damage.
Removethe spark arrester, if equipped, and inspect for
damageor carbon blockage,if replacementparts are required,
make sure to use only original equipment replacementparts.
WARNING
Exhaust heat/gases could ignite
combustibles, structures or damage fuel
tank causing a fire, resulting in death or
serious injury.
Contact with muffler area could cause burns resulting in
serious injury.
, DO NOTtouch hot parts and AVOID hot exhaust gases.
Allow equipment to cool before touching.
Keep at least 5 feet (1.5 m) of clearanceon all sides of pressure
washer including overhead.
it is a violation of California PuNic ResourceCode, Section
4442, to use or operate the engine on any forest=covered,
brush=covered,or grass=coveredland unless the exhaust
system is equipped with a spark attester, as defined in Section
4442, maintained in effective working order. Other states or
federal jurisdictions may havesimilar laws.
Contact the original equipment manufacturer, retailer, or dealer
to obtain a spark attester designed for the exhaust system
installed on this engine.
Replacement parts must be the same and installed in the same
position as the original parts.
NOTICE You can purchase new air filter elements by calling
1-800-4-NIY-HONIE (409°4003}.
19

Publicidad

Tabla de contenido
loading

Tabla de contenido