Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
E N G L I S H
•
During the boot sequence the pump control system identifi es any trigger operation as a potential malfunction and
prevents the motor from starting. The LCD screen will display 'BUTTON FAULT' in this instance. Reset by switching off the
power supply for 10 seconds.
•
Ensure that the placing tool is positioned below the pump reservoir tanks. Depress and release the placing tool trigger
switch a few times to almost the full stroke of the tool to circulate hydraulic fl uid and expel any air from the tool.
•
Observe action of tool. Check for fl uid leaks and ensure that in the idler mode the piston is in the fully forward position.
The placing tool will now be primed.
•
Switch off the mains power supply to the hydraulic pump unit and then disconnect the placing tool from the pump
unit in reverse order to that described above.
•
Now connect the placing tool to the primed hydraulic hose kit and electrical control cable. Then connect hydraulic hose
kit quick couplers and the electrical control cable to the pump unit.
•
Attach the nose assembly to the tool as per the instructions in the relevant nose assembly datasheet.
•
Switch on the mains supply to the hydraulic pump unit as described above.
•
Depress and release the placing tool trigger switch a few times to almost the full stroke of the tool to circulate hydraulic
fl uid.
•
The placing tool is now ready for use.
4. OPERATING INSTRUCTIONS
4.1 TO INSTALL AN AVBOLT® FASTENER
For further information regarding this fastener, refer to the nose assembly data sheet as listed in the table in section 2.3. The
information below is for guide use.
•
Check work and remove excessive gap. Gap is the space between components of the Joint.
•
Put Avbolt® fastener into hole.
•
Push nose assembly onto the pin until the nose assembly anvil stops against the collar. Tool and nose assembly must be
held at right angles (90°) to the work.
•
Depress tool trigger switch to start installation cycle.
•
When the forward motion of the nose assembly anvil stops and the pintail breaks off , release the trigger. The tool will
go into its return stroke and push off the installed fastener. At the end of the return stroke the jaws will partially release
the expended pintail which can then be pushed through the jaws with the next installation and then ejected through
the rear of the tool.
•
Once the installed fastener has been ejected, the tool and nose assembly is ready for the next installation.
4.2 TO INSTALL AN AVDELOK® FASTENER
For further information regarding this fastener, refer to the nose assembly data sheet as listed in the table in section 2.3. The
information below is for guide use.
•
Check work and remove excessive gap. (Gap is the space between components of the Joint. Gap is excessive if not
enough pintail sticks through the collar for the nose assembly jaws to grab onto).
•
Put Avdelok® fastener into hole.
•
Slide Avdelok® collar over the pin. (The beveled end of the collar must be towards the nose assembly and tool.) Push
nose assembly onto the pin until the nose assembly anvil stops against the collar. Tool and nose assembly must be held
at right angles (90°) to the work.
•
Depress tool trigger switch to start installation cycle.
•
When the forward motion of the nose assembly anvil stops and the pintail breaks off , release the trigger. The tool will
go into its return stroke and push off the installed fastener. At the end of the return stroke the jaws will partially release
the expended pintail which can then be pushed through the jaws with the next installation and then ejected through
the rear of the tool.
•
Once the installed fastener been ejected, the tool and nose assembly is ready for the next installation.
CAUTION – Do not attempt to break off a pintail without the installation of a collar as this will cause the unsecured
portion of the Avdelok® or Avbolt® pintail to eject from the nose at a high speed and force.
12
O R I G I N A L I N S T R U C T I O N
Publicidad
Capítulos
Tabla de contenido
