Fontanot genius 010 Manual Del Usuario página 8

remembering that the treads must still be free to rotate (Fig. 1) (Fig. 2).
Fixing landing
16. Move component 047009 towards ceiling. Determine the position, keeping a distance of about 15 cm from
the outer edge of the landing, drill with a 14 mm bit and definitively secure, using components 008001 (Fig. 1)
(Fig. 2).
17. Fix components 047009 to landing, using components 011053 (drill landing with a 4.5 mm bit).
18. Position components 132016 (Fig. 1) (Fig. 2).
Assembly of 010 railing (go to point 35 for model 020)
19. Starting from the top, fit balusters 127010, with parts 033142 and 002040, onto corner treads with a height
of about 97.5 cm.
20. Cut sections of handrail 140053 to length; assemble with part 046011, placing part 031076 between them.
For optimal fixing, the handrail must follow about 1/8 of a turn from the contact point.
21. Fix handrail to balusters with parts 002031; keep balusters vertical. Insert angle parts 033103, 033105
and 033107 with screws 012014 and 001017 for changes of direction. Apply end caps 033103 to ends of
handrail with parts 011069 and 004034, drill with a 6 mm bit (Fig. 1) (Fig. 11).
22. Position the first 127010 baluster; adjust the height according to the balusters already mounted. Fix
component 033142 to the floor using a Ø 8 mm bit, so that it corresponds with the first baluster. Use
elements 011053, 008004, and 001004 (Fig. 1).
23. Cut a piece of baluster 127012 to length to obtain spacers to connect treads; lock in place with parts
001010.
24. Definitively tighten component 005008 (Fig. 5).
25. Insert the steel cables into the 034041 parts on the banisters, positioning parts 031098 and 001012 on
each end of the banisters and on one intermediate baluster positioned between the two ends of the banister
side. Fasten the cables at one of the two ends using parts 031098 and 001012, leaving about 15mm
protruding from parts 034041; cover with articles 034042 and 001012. Tighten the cables by hand and lock
parts 031098 and 001012 respectively working from the lower to the higher end of the steel cable. Once
the final parts 031098 and 001012 have been fastened, cover the ends of the cables with adhesive tape to
prevent them from unravelling whilst being cut. Cut the cables at a distance of 15 mm from parts 034041.
Remove the tape and cover with articles 034042 and 001012 (Fig. 1) (Fig. 11).
26. Complete assembly of accessories, fitting components BF2 into the lower part of balusters 127010 on
corner treads and into upper part of lateral spacers 127012 (Fig. 1) (Fig. 11).
Assembly of 010 balustrade
27. Screw part 033063 onto stay 046036 with screw 011038 (Fig. 1).
28. Position components 033063 on landing, using components 002040 and 001004. Drill landing with a 5 mm
bit, keeping a distance between centres that allows at least four balusters to be fitted.
29. Position balusters 127014, with components 033078 facing outwards, and tighten component 001004 (Fig. 1).
30. Fix straight handrail 140053 using components 002031 (Fig. 1).
31. Depending on position and presence of walls around the stairwell, it may be necessary to position one or two
extra balusters 127014.
32. In this case, a space must be considered that is at the same distance from the other balusters or from the
wall. Drill landing with a 4.5 mm bit and assemble with components 033063, 001004 and 002040 (Fig. 1).
33. Assembly of floor-mounted balustrade, if applicable (Fig. 13)
Determine the position of the posts on the floor, on average one every 28 cm and at a distanza of 8 cm
from the edge. Drill with a Ø 10 mm bit and insert the 046015 components, fixing them with chemical resin
(not supplied). Assemble components 033063 with components 009002 and 005001. Insert the 127014
balustrade balusters (H= 910 mm) into the 033063 components, with the 126034 reinforcing baluster
about every metre, and lock them with components 001004. Fix the balusters to the wall using component
033010 and items 008004, 011053 and 033056 (drill with an Ø 8 mm bit). Determine the length of
the handrails and cut off the excess quantity. Assemble the 140053 handrails to the balusters with the
002031 components using items 031076 and 046011. Assemble any 033103, 033105, 033107 connecting
components and the 033103 terminal components.
34. Insert the steel cables into the 034041 parts on the banisters, positioning parts 031098 and 001012 on
each end baluster of the banisters and also on one intermediate baluster positioned between the two ends
of the banister side. Fasten the cables at one of the two ends using parts 031098 and 001012, leaving
about 15mm protruding from parts 034041; cover with parts 034042 and 001011. Tighten the cables by
hand and lock parts 031098 and 001012 respectively working from the lower to the higher end of the steel
8 - Genius 010 - 020 Q