Publicidad
Idiomas disponibles
Idiomas disponibles
bit (Fig. 1) (Fig. 8). Fix handrail to balusters with parts 002031; keep balusters vertical. Insert angle parts
033103, 033105 and 033107 with screws 012014 and 001017 for changes of direction.
Assembling 040 floor baluster (go to point 24 if not present)
22. Determine the position of the posts on the floor, on average one every 28 cm. Drill with a 10 mm bit and
insert items 046010, fixing them with chemical resin (not supplied). Fit the 033063 items with parts
009002 and 005001. Insert the 121019 balusters (H=910 mm) into items 033063, with the reinforcement
baluster 033092 about every metre, and lock them with the 033101 items. Fix the balusters to the wall
using element 033010 with articles 008004, 011053 and 033056 (drill with an 8 mm bit). Fit the 140010
handrail with the 002031 elements. Fit any connecting items 033103, 033105, 033107, and end items
033103 (Fig. 14).
23. Insert the steel cables 004041 into the parts 034035 on the balusters, positioning the parts 004048 in
correspondence to the balusters at the end of the railing side. Secure the cables on one of the two ends
using the parts 004048 and 001011. Cut and secure the cables on the opposite end using the parts
004048, 001011 and 011040 (cover the cable ends with some adhesive tape to prevent them from fraying
when you cut them). Tighten the cables by screwing in the part 011040 in sequence from top to bottom (Fig. 1)
(Fig. 8).
Assembly of 030 railing
24. Finally, fit the 116006 support base, complete with tread, inserting the 031078 spacers, as calculated
earlier, and without definitively tightening component 003039 or drilling holes in the floor (Fig. 2).
25. Fit components 005036, C63, 011064 onto the staircase balusters 122011 (Fig. 2) (Fig. 13)
26. If necessary, cut the lower part of the 122011 balusters to obtain a railing height of about 100 cm. Insert
the 122011 balusters to connect the treads, starting from the top, on the side where the railing is needed.
Position the balusters using article C63, with the holed part facing upwards. Tighten components 001010,
taking care that they are vertical (Fig. 2).
27. Cut a piece of baluster 122011 to the necessary length to obtain spacers to connect treads. Insert lateral
connection spacers and secure them at the top with components 001010 and on the lower side with part
001004 in part BE5 (Fig. 2).
28. Check that the entire staircase is vertical and trace on the floor the centre of the holes in the plate of base
support 116006. Remove the first and second treads and drill the floor with a 14 mm bit; insert parts
008021 and definitively tighten them. Replace the treads removed earlier (Fig. 2). If necessary, cut the 1st
post, insert the reinforcing part 046050 and fix it to the floor with items 002040, BF1, and 008004.
29. Fix the staircase to the wall using components 033010 and items 008004, 011053 and 033046 (drill with
an 8 mm bit) (Fig. 10).
30. Cut sections of handrail 140010 to length; assemble with part 046011. For optimal fixing, the handrail must
follow about 1/8 of a turn from the contact point.
31. Fix the handrail to the balusters with parts 002031; keep the balusters vertical. Insert angle parts 031061,
031071 and 031072 with screws 012014 and 001017 for changes of direction. Apply 031061 end caps to
the ends of the handrail with parts 004034 and 011069 (Fig. 2) (Fig. 9).
32. Determine the position of the intermediate balusters. Drill with a 4.5 mm bit; assemble parts BF1 with screw
002040.
33. Cut the intermediate balusters at a height that can be determined on the staircase itself. Insert the balusters
in parts BE5, tighten with components 001004 and fix them to the handrail with parts 002031; keep the
balusters vertical (Fig. 2) (Fig. 9).
Assembling 030 floor baluster (go to point 35 if not present)
34. Determine the position of the posts on the floor, on average one every 12 cm. Drill with a 10 mm bit and
insert items 046010, fixing them with chemical resin (not supplied). Fit the 033008 items with parts
009002 and 005001. Insert the 122014 balusters (H=910 mm) into items 033008, adding the 126009
reinforcement baluster about every metre, and locking them with the 001004 elements. Fix the balusters to
the wall using element 033010 with articles 008004, 011053 and 033046 (drill with an 8 mm bit). Fit the
140010 handrail to the balusters using the 002031 elements. Fit any connecting items 031072, 031071
and end items 031061 (Fig. 13).
Assembly of wall fixings and accessories
35. Insert the 031075 components in the treads and the BE7 / 031054 elements in the lower part of the
121019 / 122011 balusters so that they correspond with the corner treads and, in the upper part, with the
12 - Genius 030 - 040 RA
Publicidad
