Associated 6001A Manual De Instrucciones página 4

ASSEMBLY INSTRUCTIONS
Attach the handle to the charger using the four screws provided. Attach the front leg to the base with
the four hex head screws provided. To attach wheels and axle to the base, tap one axle nut onto the
axle with a hammer, slide one wheel onto the axle. Push the axle through the base, place wheel on
opposite side. Tap axle nut onto the axle with a hammer.
OPERATING INSTRUCTIONS
CAUTION
- This battery charger must be fully assembled before operating. Failure to do so may
result in risk of injury.
USE OF INSTRUMENT PANEL:
The MINUTES CHARGE timer has an OFF position, a CONTINUOUS CHARGE position and a timed
charge range from 0 to 120 minutes.
a. OFF - Always make sure the timer is in the OFF position before connecting or disconnecting the
clamps from the battery. The charger will not charge with the timer in this position.
b. CONTINUOUS CHARGE - This position is used for slow charging or parallel charging and will not
turn the charger off. Do not use this position for fast charging.
c. 0 to 120 MINUTES TIMED CHARGE - The timer will automatically turn the charger off at the end of the pre-set charging time. Turn the
timer past 20 before setting the desired time.
d. VOLTS CHARGE AND AMPS CHARGE - These switches are used to regulate the output voltage and current of the battery charger.
TO CHARGE BATTERIES
Make connections to the battery per the instructions in preceding section of this manual. Determine the battery voltage and turn the VOLTS
CHARGE switch to the lowest appropriate setting. Turn the AMPS CHARGE switch to "LO". Turn the timer on. If a higher rate of charge is
desired, advance the AMPS CHARGE switch to a higher position. If the charge rate is still not satisfactory, return the AMPS CHARGE switch
to "LO" and advance the VOLTS CHARGE switch one position. Adjust the AMPS CHARGE switch to the desired rate.
BOOST STARTING
Turn off all lights and accessories in the vehicle.
Connect the charger to battery per previous instructions. Charge the battery at least five minutes. Make sure the battery is accepting current
before setting charger to "START". Always start on the lowest amperage crank setting. Put the switch in the "START" position. Start the car
with the charger connected to the battery. Follow the duty cycle on the unit. Turn the switch to OFF and remove the AC power cord from the
electric outlet before disconnecting the DC clamps.
DIESEL VEHICLES
Diesel engines have special starting requirements due to the high compression required to ignite the fuel mixture. Because of this, the starter
motors have to work harder which requires the battery to deliver a large amount of power for a period of time. Adequate voltage must be
supplied also to insure the glow plug will have enough power to preheat the chamber. When attempting to start a diesel vehicle, always fast
charge the battery at least five minutes. If time permits, charge the battery as long as possible or until the battery reaches 75% state of
charge. Make sure the battery is accepting current before setting charger to "START". Always start on the lowest amperage crank setting.
With the charger "ON" and attached to the battery, attempt to start the vehicle. Do not crank the engine more than 20 seconds in a five-minute
period. While allowing the starter to cool, allow the charger to continue to charge the battery.
If the vehicle has two batteries installed, read the "VEHICLES WITH TWO BATTERIES" section of this manual.
VEHICLES WITH TWO BATTERIES
Many diesel vehicles and service vehicles are equipped with two batteries. This is to provide the vehicle with greater starting power capacity
or longer reserve capacity to provide power for accessories. These batteries are wired into a parallel circuit. Because of this, it will take twice
as long to charge these batteries as indicated in the LENGTH OF CHARGE table. If one battery is charged and the other discharged, the
discharged battery should be removed from the vehicle and checked. When attaching the charger to this type of vehicle the charger should
be attached to the battery which is wired closest to the starter. This allows the charger to provide maximum starting power to the starter motor
by minimizing the voltage drop in the engine cables.
PARALLEL CHARGING
This charger may be used to parallel charge up to
10 batteries with a bus bar kit, or by using a
minimum 6AWG gauge booster cables to connect
the batteries together in parallel.
CAUTION:
Do not connect 6 and 12 volt
batteries in parallel with each other.
POS(+) POS(+)
BATTERY BATTERY
NEG(-) NEG(-)
4
POS(+)
RED CLAMP
BATTERY
BLACK CLAMP
NEG(-)
OUTPUT CABLES
FROM CHARGER