Campingaz PARTY GRILL 400 Instrucciones De Empleo página 18

D - CONNECTING THE GAS CYLINDER
Use a regulator compliant with EN 12864 or EN16129.
Campingaz's regulator is recommended (see section § C-1).
An adjustment valve must be present on the gas cylinder or
on regulator.
When replacing an empty cylinder, read Section § F:
"Removing or changing the gas cylinder".
When installing or removing a gas cylinder, always operate
in an open, very well-ventilated place, never in the presence
of a flame, spark or any other source of heat (cigarette,
electrical appliance, etc.), and away from other persons or
inflammable materials.
1. Place the gas cylinder on the ground, behind or next to
the appliance.
2. Close the valve on the regulator or gas cylinder.
(Fig. 7-A)
3. Close the control knob on the appliance by turning it
towards "O". (Fig. 7-B)
4. Screw or push the regulator onto the cylinder or onto the
valve on the gas cylinder.
5. Check that the air holes in the burner tube, close to the
injector, are not obstructed by dust or cobwebs.
GB
D-1 CHECKING FOR GAS LEAKS
Do not check for leaks using a flame. Use a gas leak
detecting liquid.
1. (Fig. 9-A) Close the valve on the regulator or gas cylinder.
2. (Fig. 9-B) Apply gas leak detecting liquid to the cylinder
/regulator / hose / appliance joints. The control knob
should remain closed: off position (O) (Fig. 9-C).
3. (Fig. 9-D) Open the gas supply (valve on the regulator
or cylinder).
4. Any gas leaks will be indicated by bubbles.
5. Shut off the gas supply (valve on the regulator or
cylinder).
6. The leak can be stopped by tightening any hose
connection or replacing any faulty component. The
appliance must not be used until the leak is stopped.
Important:
An overall inspection and leaks check must be carried out at
least annually and always after changing the gas cylinder.
E - OPERATION
SAFETY PRECAUTIONS
Do not use your appliance at a distance closer than 20 cm
to a wall or flammable object, nor closer than 1 metre to
a ceiling.
Before lighting the appliance, make sure to fill the reservoir
with water to "MAXI" level, regardless whether the
appliance is to be used as a stove or a grill.
WARNING: Accessible parts may be very hot. Keep young
children away.
Never touch the burner during or just after using the
equipment.
Position the appliance on a stable, horizontal surface and
do not move when in use.Do not use a cooking vessel
smaller than 12 cm or larger than 20 cm in diameter.
In the event of a leak (smell of gas), close all valves.
Wait for the appliance to cool down completely before
handling it for storage.
After use, always close the valve on the regulator or gas
cylinder.
E-1 INSTALLING COOKING PLATES
Using the appliance as a grill (Fig. 10-A / B)
1. (Fig. 10-ii) Fill the reservoir with water to the "MAXI" level
(marked on wall of reservoir).
2. (Fig. 10-ii) Place in the pan support (5), with its three feet
resting on the supports on the wall of the reservoir.
3. (Fig. 10-ii) Place the heat distributor (4) over the pan
support, with its edge resting on the notches of the pan
support feet.
4. Place one of the cooking plates (griddle (2) or grid (3))
over the pan support (5), with its edge resting on the
notches of the pan support feet.
Griddle (2) placement (Fig. 10-A)
The three feet on pan support (5) must be in line with and
inserted through the three slits around the edge of the
griddle (2) (Fig. 10-i).
Grid (3) placement (Fig. 10-B)
Make sure to rotate the grid (3) to a position that the
u-shap spacer rests right on the feet of the pan support
(5) (Fig. 10-iv).
IMPORTANT: Never use more than one cooking plate at
the same time. Heat distributor must be placed beneath the
cooking plate prior to use. Never put cooking vessels (pan,
wok etc.) on cooking plate (2 / 3) or heat distributor (4).
Using the appliance as a stove (Fig. 10-C)
1. (Fig. 10-ii) Fill the reservoir with water to the "MAXI" level
(marked on wall of reservoir).
2. (Fig. 10-ii) Place in the pan support (5), with its three feet
resting on the supports on the wall of the reservoir.
3. Flid the lid (1) over and place it on the pan support (5) to
use it as a cookig vessel (wok). Or place other cooking
vessel (pan etc.) on the pan support, centered over
the burner. Ensure that the flame does not exceed the
underside of the cooking vessel.
IMPORTANT: Cooking plate (2 / 3) and heat distributor (4)
must be taken away when using the appliance as a stove.
Never put cooking vessels (pan, wok etc.) on cooking plate
(2 / 3) or heat distributor (4).
18