•
Do not modify this tool. Modifications can reduce
the effectiveness of safety measures and increase
the risks to the operator.
•
Whipping hoses can cause severe injury. Always
check for damaged or loose hoses and fittings.
WARNING: (Air and Supply and Connections)
•
Do not use oxygen, combustible gases, or bottled
gases as a power source for this tool as the tool
may explode, possibly causing injury.
•
Do not use supply sources which can potentially
exceed 200 PSI (13.8 Bar) as tool may burst,
possibly causing injury.
•
The connector on the tool must not hold pressure
when air supply is disconnected. If a wrong fitting
is used, the tool can remain charged with air after
disconnecting and thus will be able to after the air
line is disconnected possibly causing injury.
•
Before connecting the tool to the air inlet, ensure
the trigger is not blocked in the on position by
an obstacle.
•
The pneumatic tool must be fitted and connected
to the compressed air network via quick
disconnects to facilitate shutdown in the event
of danger.
•
In the event of blockage, release the trigger
and disconnect the tool from the compressed
air network.
•
Be sure all hoses and fittings are the correct size
and are tightly secured.
•
Mesh air strainer at air inlet occasionally becomes
clogged with debris, blocking air supply, and
decreasing the tool's performance. If this occurs
the mesh air strainer needs to to be cleaned.
WARNING: Do not operate tool if:
•
There is any damage to air hose or fitting.
•
The tool leaks air.
•
The tool has received a sharp blow, malfunctions
or is dropped or damaged in any manner. Return
tool to the nearest authorized service facility for
examination, repair, or mechanical adjustment.
•
Warning labels are missing or damaged.
•
Tool is not in proper working order. Tags and
physical segregation shall be used for control.
WARNING: When operating the tool:
•
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
•
Anticipate and be alert for sudden changes in
motion during start up and operation of any
power tool.
•
Do not use in wet conditions.
•
Always handle the tool with care.
•
Never engage in horseplay.
•
Never point the tool at yourself or others.
•
Keep bystanders and children away while
operating tool.
•
Respect tool as a working implement.
•
Stay alert, focus on your work and use common
sense when working with tools.
•
Do not use tool while tired, after having consumed
drugs or alcohol, or while under the influence
of medication.
•
Do not overreach. Only use in a safe
working place.
•
Keep proper footing at all times.
•
This tool produces SPARKS during operation.
NEVER use the tool near flammable substances,
gases or vapors including lacquer, paint, benzine,
thinner, gasoline, adhesives, mastics, glues or any
other material that is–or the vapors, fumes or
byproducts of which are–flammable, combustible
or explosive. Using the fastenerer in any such
environment could cause an EXPLOSION resulting
in personal injury or death to user and bystanders.
•
For overhead work, wear a safety helmet.
•
If the tool appears to malfunction, remove
from use immediately and arrange for service
and repair.
•
The tool is not electrically insulated. Never use
the tool if there is any chance of it coming into
contact with live electricity.
•
Do not lock, tape, wire, etc., the on/off trigger in
the run position. The trigger must always be free
to return to the "off" position when it is released.
•
Never lay a tool down unless the working
attachment has stopped moving.
•
Always ensure that the forward/reverse switch is
in the desired position before starting the tool.
•
Do not use sockets with excessive wear to the
input or output drives. Periodically check the
square drive on the impact wrench.Make surer
the socket, extension bar, or other attachment is
securely fitted before operating tool.
•
When loosening fasteners first ensure that there
is sufficient clearance behind the tool to avoid
hand entrapment. The tool will move away from
the threaded joint as the nut/bolt is loosened and
rides up the thread, moving the tool with it.
WARNING: Disconnect tool:
•
When not in use.
•
Before making adjustments.
•
When performing any maintenance or repairs.
•
When elevating, lowering or otherwise moving
tool to a new location.
•
When tool is outside of the operator's supervision
or control.
•
When moving to a different work area, as
accidental actuation may occur, possibly
causing injury.
WARNING: When maintaining the tool:
•
Always shut off air supply, and disconnect tool
from air supply when not in use.
English
3