MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supply before
making any adjustments or removing/installing
attachments or accessories. An accidental start‑up
can cause injury.
Lubrication
Air tools require lubrication throughout the lifetime of
the tools.
The air motor and bearing uses compressed air to power
the tool. The compressed air contains moisture that will rust
the air motor and other parts in side of the tools, therefore
lubrication is required daily. Failure to lubricate the air tool
properly will dramatically shorten the life of the tool and will
void the warranty
CAUTION: This air tool requires lubrication BEFORE
initial use, also before and after each additional use.
To Lubricate the Air Tool Manually
1. Remove any attachment on the drive of air tools, such
as: sockets, chisels and etc.
2. Disconnect the tool from the air supply source, place
the air inlet face up.
3. Depress the trigger and place about 1 teaspoon of air
tool oil into the air inlet. (Depressing the trigger will help
circulate oil in the motor.)
nOTE: Use SAE #10 weight oil if air tool oil is
not available.
WARNING: Keep out of the reach of children. If
taken internally, do not induce vomiting, call a
doctor immediately.
WARNING: Any excess oil in the motor is immediately
expelled from the exhaust port. Always direct exhaust
port away from people or objects.
4. Connect the tool to an air source, cover the exhaust end
with a towel and run for about 20 to 30 seconds.
5. After every 48 hours or operation, or as experience
indicates, inject about 1 teaspoon of approved
pneumatic grease into the grease fitting.
Storage
The air tool must be lubricated before storing.
Follow Steps 1–3 in To Lubricate the Air Tool Manually.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by Mac Tools, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only Mac Tools
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact Mac Tools, 505 North Cleveland
Ave., Westerville, Ohio 43082, call 1-800-MAC-TOOLS
(1-800-622-8665) or visit our website www.mactools.com.
UK Customer Service:
Mac Tools UK, Europa Court, Sheffield Business Park,
Sheffield, England S9 1XE
Tel: +44 (0) 1142 917266 Fax: +44 (0) 1142 917131
Email: customerservices@mactools.co.uk
Repairs
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a Mac Tools
factory service center or a Mac Tools authorized
service center. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
•
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
•
COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
•
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.mactools.com.
Two Year Limited Warranty
Mac Tools will repair, without charge, any defects due
to faulty materials or workmanship for two years from
the date of purchase. This warranty does not cover part
failure due to normal wear or tool abuse. For further detail
of warranty coverage and warranty repair information,
visit www.mactools.com or call 1–800-MAC-TOOLS
(1–800–622–8665). This warranty does not apply to
accessories or damage caused where repairs have been
made or attempted by others. THIS LIMITED WARRANTY
IS GIVEN IN LIEU OF ALL OTHERS, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, AND EXCLUDES ALL INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow
limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential
English
7