Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
SPECIFICATIONS
Min. hose diameter
Dimensions (L X H X W)
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
IMPORTANT SAFETY
INSTRUCTIONS
WARNING: WHEN USING THIS TOOL, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED TO REDUCE THE RISK OF PERSONAL
INJURY, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1.
For personal safety and proper operation and
maintenance of the tool, read this instruction
manual carefully before using the tool.
2.
Always wear safety glasses to protect your
eyes from dust or nail injury. The safety
glasses should conform with the requirements
of ANSI Z87.1.
WARNING:
It is an employer's responsibility to enforce
the use of safety eye protection equipment by
the tool operators and by other persons in the
immediate working area.
3.
Wear hearing protection to protect your ears
against exhaust noise and head protection.
Also wear light but not loose clothing. Sleeves
should be buttoned or rolled up. No necktie
should be worn.
4.
Rushing the job or forcing the tool is
dangerous. Handle the tool carefully. Do not
operate when under the influence of alcohol,
drugs or the like.
5.
General Tool Handling Guidelines:
(1)
Always assume that the tool contains
fasteners.
(2)
Do not point the tool toward yourself or
anyone whether it contains fasteners or
not.
(3)
Do not actuate the tool unless the tool is
placed firmly against the workpiece.
(4)
Respect the tool as a working implement.
(5)
No horseplay.
Model
Air pressure
Nail length
Nail capacity
Net weight
265 mm X 269 mm X 117 mm (10-3/8" X 10-5/8" X 4-5/8")
USB087-1
(6)
(7)
(8)
6.
An improperly functioning tool must not be
used.
7.
Sparks sometimes fly when the tool is used.
Do not use the tool near volatile, flammable
materials such as gasoline, thinner, paint, gas,
adhesives, etc.; they will ignite and explode,
causing serious injury.
8.
The area should be sufficiently illuminated to
assure safe operations. The area should be
clear and litter-free. Be especially careful to
maintain good footing and balance.
9.
Only those involved in the work should be in
the vicinity. Children especially must be kept
away at all times.
10. There may be local regulations concerning
noise which must be complied with by keeping
noise levels within prescribed limits. In certain
cases, shutters should be used to contain
noise.
11.
Do not play with the contact element: it
prevents accidental discharge, so it must be
kept on and not removed. Securing the trigger
in the ON position is also very dangerous.
Never attempt to fasten the trigger. Do not
operate a tool if any portion of the tool
operating controls is inoperable, disconnected,
altered, or not working properly.
12. Operate the tool within the specified air
pressure on the tool label for safety and longer
tool life. Do not exceed the recommended max.
operating pressure. The tool should not be
connected to a source whose pressure
potentially exceeds 14.0 kgf/cm
2
AN453
2
4.5 - 8.5 kgf/cm
G (65 - 120 PSIG)
19 mm (3/4") - 45 mm (1-3/4")
120 pcs.
6.5 mm (1/4")
2.4 kg (5.2 lbs)
Do not hold or carry the tool with a finger
on the trigger.
Do not load the tool with fasteners when
any one of the operating controls is
activated.
Do not operate the tool with any power
source other than that specified in the tool
operating/safety instructions.
2
G (200 PSIG).
Publicidad
Tabla de contenido
