Gearbox; Rear Bar; Rear Rollers; Stopping The Machine - breviglieri mekfarmer 220 Instrucciones De Empleo Y Mantenimiento

DRIVING TORQUE VALUES Nm
Class
M8x1
M10x1,25
M12x1,25
M14x1,5
M16x1,5
M18x1,5
M20x1,5
M22x1,5
M24x2
If the tines clog, it is strictly forbidden to attempt to clean the
machine whilst it is operating.
First disengage the PTO, stop the tractor and engage the
parking brake.
Wait until all moving parts have come to a complete stand-
still, then proceed with the cleaning operations with the ut-
most care.

4.9 GEARBOX

The tine rotors can spin at various speeds, depending on the gear
pairs mounted in the gearbox.
It also allows the soil to be broken up to various degrees depend-
ing on its nature, the amount of moisture it contains, the ground
speed, etc.
Only use the pairs indicated in the table
GEARBOXES - 1000 rpm PTO
Gears
A B
18
A (PTO)
19
B
332
The faster the rotors spin, the more the soil is crumbled, but trac-
tor power draw and blade wear will also be greater.
You are advised to use the lowest rotation speed able to work the
soil in the required way.
Carry out these simple operations in both gearboxes to vary the
speed of the rotors:
- Remove the screws that fix the rear cover of the gearbox (5 Fig.
1) and take off the cover. Take care, as oil could spill out.
- Remove the gears from the shafts.
- Fit the required pairs of gears on to the shafts.
- Fit back the cover and re-tighten the screws.
Make sure you use the right gears as gears of different pairs can-
not be mounted.

4.10 REAR BAR

To level and crumble the soil to a greater degree, the harrow has
a levelling bar positioned behind the tines.
It can be adjusted in height by means of crank screws (6 Fig. 1).
It is advisable to start work with the bar in the upper position and
6.6 8.8 10.9
15 26 36
30 52 74
51 91 127
81 143 201
120 214 301
173 308 433
242 431 606
321 571 803
411 731 1028
DANGER
A B A B A
19 17
18 20
370 298
mekfarmer 220
to then adjust it to the required setting.
Make the adjustments by keeping the bar at the same distance
12.9
from the soil as far as possible.
44
Avoid using the bar at depth as it could be damaged.
88
Whenever the position of the rear roller must be changed, adjust
again in order to skim over the ground.
153
241
361

4.11 REAR ROLLERS

520
The machine can be equipped with various types of roller. The
727
main ones are: Packer roller, Cage roller, Spiked roller.
964
Packer roller:
1234
- This is used to crumble the soil worked by the tines to a further
degree and to guarantee a compact surface, optimum for seed-
ing. It has a bearing effect if the seed drill is mounted in a com-
bined configuration. It is excellent for dry and hard soil.
Cage roller:
- This is used for soil of medium consistency and when the de-
gree of humidity is low. It prepares the soil for seeding but does
not compact the surface.
Spiked roller:
- This is used for damp, clayey soils and in difficult situations. It
does not compact the soil but levels it at the rear of the ma-
chine.

4.12 STOPPING THE MACHINE

At the end of the job, the operator must:
- Disengage the tractor PTO.
- Lower the machine to the ground by means of the power lift.
- Stop the tractor and engage the parking brake.
- Make sure that all parts of the machine are at a standstill.
Only after the above mentioned operations have been carried out
may the operator leave the tractor unattended.

4.12.1 PARKING

B
- At the end of the job, the machine must be parked on a flat,
20
suitable surface.
- Stop the tractor and apply the parking brake.
17
- With the tractor stopped and all components at a complete stand-
413
still, remove the driveline from the PTO of the tractor.
- Unhitched the machine from the tractor.
The place in which the machine is parked must be:
- Dry.
- Sheltered from adverse weather conditions.
- Guarded or locked up to prevent children or unauthorized
persons from freely accessing the machine.
If the machine is to remain idle for a long period of time, lubri-
cate the parts subject to wear and store the machine in a dry,
sheltered place, covered with a plastic sheet.
This will ensure that the machine is in the ideal condition
when required again.
SECTION 5
- 26 -
WARNING
CAUTION