Troubleshooting - Hozelock KILLASPRAY Manual De Instrucciones

Ocultar thumbs Ver también para KILLASPRAY:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 8
33794 KillaSpray5/7/10 Inst
GB
k
s
illa
pray
Instructions & Warnings
• Before carrying out any maintenance on this sprayer, it is
essential to depressurise the bottle by activating the pressure
release valve.
• This sprayer is intended for use with water-based solutions of:
insecticides, fungicides, weedkillers & fertilizers.
• Always follow the chemical suppliers instructions, as well as
the instructions supplied with this sprayer.
Always wear protective clothing, goggles, face mask and
gloves.
Avoid inhaling spray mist.
Avoid skin contact with chemicals.
Always work in a well ventilated area.
Take care to protect children pets & fish from exposure to
chemicals.
Always wash hands thoroughly after use & especially before
eating.
Always wash any contaminated clothing.
Seek medical attention if spray gets in your eyes or you
develop any symptoms after spraying.
Do not spray near food or food preparation areas.When
spraying crops, pay particular attention to the chemical
manufacturers advice on time before crops can be eaten.
Do not spray any solvent e.g. White spirit.
Spray only thin watery solutions; thicker mixtures will clog
the nozzle.
Powdered chemicals can be sprayed successfully if they are
completely soluble in water. If they are not, or the solution
tends to settle, spraying can still be successful if the mixture
is continually agitated.
If the material to be sprayed contains sediment, strain the
liquid into the sprayer bottle.
Do not over pressurise the bottle, or tamper with the
pressure release valve. The pressure release valve is designed
to release excess pressure do not interfere with it or force it
to remain closed.
Winter Use – drain liquid from all parts and prevent damage
from freezing.
Annual maintenance – At least once per year thoroughly
clean the whole sprayer and apply silicone grease to all
moving parts & seals. Test with water, and if any washer or
seal has perished it must be replaced.
• Before carry out any maintenance on this sprayer. It is essential
to depressurise the bottle by activating the pressure release
valve.
A
Make sure all nuts are screwed hand tight before use.
B
This sprayer is made from many different types of plastic,
and although the liquid you wish to spray may be packed in
plastic, this does not guarantee it will not damage the sprayer.
If you have any doubt about compatibility contact Hozelock
consumer services. When filling the sprayer ensure that the
maximum fill level is not exceeded.
C
Ensure that the pump is screwed into the bottle tightly.
D
Operate the pressure release valve manually to ensure it is
functioning correctly and able to move.
25/10/07
Notes
13:33
Page 4
E
If the sprayer has been used with chemicals, discard safely any
unused solution after use.
F
Fill sprayer with warm water (not hot),
re-assemble the sprayer and spray some of the contents.
Repeat; check that the nozzle is free from sediment.
If necessary repeat the process until the sprayer is clean.
NB : Do not use detergent.
G
The pump O-ring should be lubricated to allow the sprayer to
pump air efficiently. Apply silicone grease regularly, to the
pump O Ring (A).
H
The nozzle cap (B) & swirl grooves (C) should be kept clean
and free of obstruction. The O-ring should be lubricated to
allow the spray pattern to be easily changed. Apply silicone
grease regularly, to the nozzle O Ring (D).
I
Keep the trigger clean and free from build up of sediment and
chemicals by regularly flushing after use. If necessary remove
and clean the shuttle in the trigger.
J
To clean or replace washers and O-ring in the dip tube.
Depressurise the bottle first, unscrew the hose nut and pull dip
tube assembly out.
• Hozelock guarantees this sprayer against any defect arising
from faulty materials or workmanship for a period of 3 years
from the date of purchase, provided that it has only been used
in accordance with these instructions. The guarantee is limited
to the repair or replacement of any defective or faulty item.
Proof of purchase must be retained.
• Hozelock extended guarantee covers the bottle and pump
mechanism only. It specifically excludes: all O-rings & seals,
the hose, and the lance assembly. These have a 12-month
guarantee, are wearing parts and are available as spares from
the retailer or from Hozelock direct.
Contact Details
Hozelock Limited
Midpoint Park, Birmingham. B76 1AB
Tel : +44 (0) 121 313 1122
Internet : www.hozelock.com
Email : info@hozelock.com

Troubleshooting

Issue
Problem
Weak or
Sprayer will not
no spray
pressurise
Obstruction
Distorted
Obstruction
Spray
Leaks
Build up of
sediment or
foreign matter on
sealing surfaces
Worn or
damaged O rings
/ Washers
Handle
Faulty non return
rises
valve (X)
Guarantee
Solution
Ensure all connections are tight
Check O rings and seals are
lubricated and show no signs of
wear or damage – replace if
required (see notes G, I & J)
There could be a blockage in the
nozzle, or the trigger or the
outlet tube
There could be a blockage in the
nozzle
Check O rings and seals are free
from dirt – Clean or replace if
required
Check O rings and seals are free
from wear or damage – replace
if required
This stops the compressed air in
the container from escaping
back into the pump
If faulty the unlocked pump
handle will rise when the
container is pressurised. To
remove the valve, lift the edge
and pull (NB take care not to
damage the sealing face of the
barrel. Replace with a new valve
by pushing firmly over the
centre hole

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

460546074610

Tabla de contenido