Functional Description - Makita 6305W Manual De Instrucciones

SAVE THESE INSTRUCTIONS
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release the
switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
Indicator lamp (Fig. 2)
The green power-ON indicator lamp lights up when the
tool is plugged to the mains. If the indicator lamp is lit but
the tool does not start even if the tool is switched ON, the
carbon brushes may be worn out, or the motor or the
switch may be defective. If the indicator lamp does not
light up, the mains cord or the indicator lamp may be
defective. When the mains cord is defective, the tool nei-
ther starts nor lights the indicator lamp. When the indicator
lamp is defective, the tool starts without the indicator lamp
lighting up.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing grip (Fig. 3)
Install the grip securely on the arm provided in a box with
the tool.
Installing or removing drill bit (Fig. 4)
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each of
the three holes and tighten clockwise. Be sure to tighten
all three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in
just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return to the original
position.
6
Drill stand
CAUTION:
• Raise the drill fully when installing the drill stand.
Stand base - - - screw M6 x 14 to be used
Lever - - - bolt M6 x 10 to be used
Remove the secured stand base from the steel carrying
case and fix it on the shoe with two screws. (Fig. 5)
CAUTION:
• Remove the grip from the tool when using with the drill
stand.
To install the lever on the arm, use two holes in the lever.
Fit the hole in the top of the lever to the protrusion of arm
and secure it with the bolt in another hole.
Secure the tool to the table or stable and level surface.
(Fig. 6)
Secure and lock the workpiece to avoid its rotation using
spindled holes provided in the base. (Fig. 7)
V base - - - Screw M6 x 16 to be used
(Fig. 8 & 9)
V base allows a drill bit to be held perpendicular to work-
piece when drilling the workpiece with round section such
as steel pipe and the like.
Secure V base with screw provided in a box with the tool.
Stopper - - - screw M 5 x 16 and washer 5
to be used (Fig. 10 & 11)
The stopper allows operator to drill a hole with the con-
stant distance away from the workpiece end.
Secure the stopper with screw and washer provided in a
box with the tool.
Sub shoe - - - screw M 6 x 16 to be used
(Fig. 12 - 14)
Use the sub shoe when the workpiece is unstable as
shown in the figures.
Secure the sub shoe on the shoe with screws (2 pcs.) pro-
vided in a box with the tool.
OPERATION
Positioning the clamper
Determine the clamper position considering the position of
the drill bit tip and the shoe according to the thickness of
workpiece.
To change the position of the clamper, first push or pull the
clamping lever and then move the lever to the desired
position. After changing, return the clamping lever to the
original position. (Fig. 15)
CAUTION:
• When changing the position of the clamper, be sure to
hold the arm before operating the clamping lever. With
the arm held, push or pull the clamping lever so that the
arm does not unintentionally move.