Makita LS1214 Manual De Instrucciones página 18

For European countries
CAUTION:
• The ring 30 mm in outer diameter is factory-installed
between the inner and outer flanges.
Return the blade guard and center cover to its original
position. Then tighten the hex bolt clockwise to secure
the center cover. Release the handle from the raised
position by pulling the stopper pin. Lower the handle to
make sure that the blade guard moves properly. Make
sure shaft lock has released spindle before making cut.
(Fig. 23)
Dust bag (Fig. 24)
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, insert
the dust nozzle into the dust spout on the blade case and
fit the bag's entry port over the dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove par-
ticles adhering to the insides which might hamper further
collection.
NOTE:
If you connect a vacuum cleaner to your saw, more effi-
cient and cleaner operations can be performed.
Securing workpiece
WARNING:
• It is extremely important to always secure the work-
piece properly and tightly with the vise. Failure to do so
can cause the tool to be damaged and/or the work-
piece to be destroyed. PERSONAL INJURY MAY
ALSO RESULT. Also, after a cutting operation, DO
NOT raise the blade until the blade has come to a com-
plete stop.
CAUTION:
• When cutting long workpieces, use supports that are
as high as the top surface level of the turn base. Do not
rely solely on the vertical vise and/ or horizontal vise to
secure the workpiece.
Thin material tends to sag. Support workpiece over its
entire length to avoid blade pinch and possible KICK-
BACK. (Fig. 25)
Sub-fence
This tool is equipped with the sub-fence which should
ordinarily be positioned as shown in Fig. 26.
However, when performing left bevel cuts, set it to the left
position as shown in Fig. 27.
CAUTION:
• When performing left bevel cuts, flip the fence over to
the left position as shown in Fig. 27. Otherwise, it will
contact the blade or a part of the tool, causing possible
serious injury to the operator.
Sub-fence R (Fig. 28)
The sub-fence R should ordinarily be installed on the
right side of the guide fence. Insert the rods of the sub-
fence R into the holes in the guide fence. Tighten the
screws to secure the sub-fence R.
CAUTION:
• When performing right bevel cuts, never use the sub-
fence R. It will contact the blade or some part of the
tool, causing a serious injury to operator.
18
Vertical vise (Fig. 29 & 30)
The vertical vise can be installed in two positions on
either the left or right side of the guide fence. Insert the
vise rod into the hole in the guide fence and tighten the
screw on the back of the guide fence to secure the vise
rod.
The vertical vise can also be secured to the rod on the
right side of the subfence R.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by tight-
ening the screw. If the screw to secure the vise arm con-
tacts the guide fence, install the screw on the opposite
side of vise arm. Make sure that no part of the tool con-
tacts the vise when lowering the handle fully and pulling
or pushing the carriage all the way. If some part contacts
the vise, re-position the vise.
Press the workpiece flat against the guide fence and the
turn base. Position the workpiece at the desired cutting
position and secure it firmly by tightening the vise knob.
CAUTION:
• The workpiece must be secured firmly against the turn
base and guide fence with the vise during all opera-
tions.
Horizontal vise (optional accessory) (Fig. 31 & 32)
The horizontal vise can be installed in two positions on
either the left or right side of the base. When performing
15° or greater miter cuts, install the horizontal vise on the
side opposite the direction in which the turn base is to be
turned.
By flipping the vise nut to the left, the vise is released,
and rapidly moves in and out. To grip the workpiece,
push the vise knob forward until the vise plate contacts
the workpiece and flip the vise nut to the right. Then turn
the vise knob clockwise to secure the workpiece.
The maximum width of workpiece which can be secured
by the horizontal vise is 200 mm.
When installing the horizontal vise on the right side of the
base, also use the sub-fence R to secure the workpiece
more firmly. Refer to the "Sub-fence R" section described
on previously for installing the sub-fence R.
CAUTION:
• Always set the vice nut to the right fully when securing
the workpiece. Failure to do so may result in insufficient
securing of the workpiece. This could cause the work-
piece to be thrown, cause damage to the blade sub-
fence or cause the dangerous loss of control of the tool.
Holders (Fig. 33)
The holders can be installed on either side as a conve-
nient means of holding workpieces horizontally. Slip the
holder rods into the holes in the base and adjust their
length according to the workpiece to be held. Then
tighten the holders securely with the screws.
CAUTION:
• Always support long workpieces level with the top sur-
face of the turn base for accurate cuts and to prevent
dangerous loss of control of the tool.