Resumen de contenidos para Escalade Sports HARVARD G02224W
Página 1
Evansville IN 47706 Please have your model number when inquiring about parts. When contacting Escalade Sports please provide your model number, date code (if applicable), and part number if requesting a replacement part. These numbers are located on the product, packaging, and in this owners manual.
Página 4
Parts Identifier (Not to Scale) P1W - White Base P1B - Black Base P2 - White Front U-Tube (1) U-Tube (1) Base Tube (2) P4 - Back Support P3 - Back Base P5 - Front Connecting Tube (2) Tube (2) Tube (2) P6 - Back Connecting P7 - Cross Tube (3)
PARTS REQUIRED: 1 pc - P11 White U-Tube 2 pcs - P2 White Front Base Tube 1. Slide White Front Base Tubes P2 into White U-Tube P11 and snap together spring locks. Figure 1 PARTS REQUIRED: 1 pc - P1W White Base U-Tube 2.Slide White Base U-Tube P1W into White Front Base Tubes P2 and snap together spring locks.
Página 10
PARTS REQUIRED: 4 pcs - H4 Allen Head Bolt 4 pcs - H9 Locknut 1 pc - T1 Allen Wrench 4 pcs - H7 Flat Washer 2 pcs - P6 Back Connecting Tube 1 pc - T2 Wrench 7. Install Back Connecting Tubes P6 to Back Support Tubes P4 using Allen Head Bolts H4,Flat Washers H7 and Locknuts H9 Use T1 Allen Wrench and T2 Wrench to tighten Bolts and Nuts.
Página 11
PARTS REQUIRED: 1 pc - P10 Cross Tube 1 pcs - P23 Rebounder 9. Slide Cross Tube P10 into Rebounder P23 as shown. NOTE: Figure 8 Elastic (stretch) loops on this side. PARTS REQUIRED: 2 pcs - H3 Allen Head Bolt 2 pc - H7 Flat Washer 1 pc - T1 Allen Wrench 10.
Página 13
13. Secure Ramp Net P18 velcro straps onto Tube P1W, Tubes P2, Tubes P5, Tubes P6, Tube P10 and Tube P11 as shown. Tube Figure 12 PARTS REQUIRED: 1 pc - P22 Touch Sensor Cloth 14. Install Touch Sensor Cloth P22 to Back Support Tubes P4 and Cross Tube P10 by securing the velcro straps around the tubes as shown.
Página 14
PARTS REQUIRED: 4 pcs - H4 Allen Head Bolt 4 pcs - H9 Locknut 1 pc - T1 Allen Wrench 4 pcs - H7 Flat Washer 2 pcs - P9 Front Support Tube 1 pc - T2 Wrench 15. Install Front Support Tubes P9 to Back Connecting Tubes P6 using Allen Head Bolts H4, Flat Washers H7 and Locknuts H9 .
Página 15
PARTS REQUIRED: 2 pcs - H4 Allen Head Bolt 1 pc - P7 Cross Tube 1 pc - P19B Touch Sensor 1 pc - T2 Wrench 4 pcs - H7 Flat Washer 1 pc - P19W Touch Sensor with Black Connector 2 pcs - H9 Locknut with White Connector 1 pc - T1 Allen Wrench...
Página 19
ADJUSTMENT AND USE OF YOUR ELECTRONIC SCORER Plug the adapter into a suitable 120v household outlet and into the back of the scoring unit. Basketball Game: Set Switch to “Basketball”: Each player has 30 seconds to make as many baskets as they can. During the first 20 seconds each basket made counts “2”...
Página 22
Por favor tenga el n úmero de modelo cuando solicite partes. Cuando se ponga en contacto con Escalade Sports,incluya el número de modelo de su producto,el c ódigo de la fecha(si lo hubiera)y la referencia de la pieza si solicita una pieza de sustituci ón.
Página 25
Piezas Necesarias (no está a escala) P1W - Tubo blanco en forma P1B - Tubo negro en P2 - Tubo frontal blanco de “U” para la base (1) forma de “U” para la para la base (2) base (1) P4 - Tubo de Soporte P3 - Tubo trasero para P5 - Tubo conector frontal (2) la base (2)
Página 30
PIEZAS NECESARIAS: 1 ud - P1B Tubo negro en forma de “U” 2 uds - P3 Tubo trasero para la base 2 uds - P4 Tubo de Soporte trasero para la base PASO 5: Conecte el tubo negro en forma de “U” para la base P1B con los tubos traseros para la base P3 hasta que entre el pasador con resorte.
DURACIÓN DE LA GARANTÍA: Este Producto está garantizado durante un período de 90 días a partir de su adquisición. COBERTURA DE LA GARANTÍA: ESCALADE SPORTS garantiza al comprador del producto original que cualquier Producto de su fábrica carece de defectos materiales o de fabricación si se utiliza para el fin para el que se han diseñado en condiciones normales y con un uso adecuado.